Filter
Top Products
SYSTEM CONFIGURATIONSYSTEM CONFIGURATION
SYSTEM CONFIGURATION 21SYSTEM CONFIGURATION 21
Delay times are only adjustable for the Dolby modes,
so you will notice that the
DELAY menu may not
be accessed when any other mode, such as a DTS or
Logic 7 option, has been selected. In addition, when a
non-Dolby Digital mode such as Dolby 3 Stereo or
Pro Logic II is selected, adjustments may be made to
the Surround speakers only.
To set the delay time for a specific input, the
DELAY ADJUST menu (Figure 7) should be
visible on your on-screen display. If the system is not
already at that point, press the
OSD Button v to
bring up the
MASTER MENU, press the
¤
Button n until the on-screen
›
cursor is pointing at
the
DELAY ADJUST line. Press the Set
Button
p to call up the menu.
NOTE: In order to adjust the Delay settings for the
surround back channels, a Dolby Digital or DTS source
must be playing. This enables the system to activate
the surround back processing mode.
Figure 7
Once the DELAY ADJUST menu is on your
screen, note that the default setting to enter the dis-
tances from the speakers to the listening position is in
feet. If your measurements are in feet, proceed to the
next step; if your measurements are made in meters,
press the
¤
Button n until the on-screen
›
cursor
is at the
UNIT line on the menu. Then, press the
‹
/
›
Buttons o so that METER is highlighted.
When the change in measurement units is made,
press the
⁄
/
¤
Buttons n to return the
›
cursor
to the
CENTER position.
With the on-screen
›
cursor pointing to CENTER,
press the
‹
/
›
Buttons o until the distance from
the center speaker to the preferred listening position is
entered. Next, press the
¤
Button n to move the
cursor to the
SURROUND line and use the
‹
/
›
Buttons o again to enter the distance from the
video display at the front of the room to the surround
speakers. Finally, if the system is configured for 7.1
operation by entering
LARGE or SMALL on
the
SURR BACK line of the SPEAKER
SETUP
menu, press the
¤
Button n again
and use the
‹
/
›
Buttons o to enter the distance
from the listening position to the surround speakers.
Remember that this last adjustment will only be needed
when you have surround back speakers installed and
Dolby Digital chosen as the surround mode.
When the speaker-to-listening-position distance has
been entered for all active speaker positions, press the
⁄
/
¤
Buttons n until the on-screen cursor is next
to
BACK TO MASTER MENU and press the
Set Button p.
The delay settings may be changed at any time
directly from the remote control by pressing the
Delay Button . CENTER DELAY will
appear in the
Lower Display Line ¯, but you
may press the
⁄
/
¤
Buttons n to select any
of the speaker groups.
Press the
Set Button p when the desired speaker
group appears, and then press the
⁄
/
¤
Buttons
n again to enter the distance from the speaker to
the listening position. Press the
Set Button p
again to enter the data. You may then press the
⁄
/
¤
Buttons n to select another speaker group to
repeat the procedure as needed, or wait five seconds
for the system to return to normal operation.
Output Level Adjustment
Output level adjustment is a key part of the configura-
tion of any surround sound product. It is particularly
important for a digital receiver such as the AVR 230,
as correct outputs ensure that you hear soundtracks
with the proper directionality and intensity.
IMPORTANT NOTES:
• Listeners are often confused about the operation of
the surround channels. While some assume that
sound should always be coming from each speaker,
most of the time there will be little or no sound in
the surround channels. This is because they are
only used when a movie director or sound mixer
specifically places sound there to create ambience
or a special effect, or to continue action from the
front of the room to the rear. Once the output
levels are properly set, it is normal for surround
speakers to operate only occasionally. Artificially
increasing the volume to the rear speakers may
destroy the illusion of an enveloping sound field
that duplicates the way
you hear sound in a movie
theater or concert hall.
• When the AVR 230 is configured for 6.1-channel
operation using a single surround back speaker, the
output level adjustments will still provide an adjustment
for separate surround back left and surround back right
positions even though your system has only one
surround back speaker. This means that the Surround
Back channel will seem to appear twice, and in 6.1
operation this is normal. The separate SBL/SBR adjust-
ments for 6.1 operation are needed to optimize the
balance between the two discrete channels within the
AVR as they are mixed for output to a single speaker.
Before beginning the output level adjustment process,
make certain that all speaker connections have been
properly made. The system volume should be set to
the level that you will use during a typical listening
session. While the AVR 230 allows you to set output
levels manually, we recommend that the EzSet system
be used when the AVR is first installed, to establish the
initial level settings.
Using EzSet
Harman Kardon’s exclusive EzSet remote makes it
possible to quickly and accurately set the AVR 230’s
output levels without the use of a sound pressure
meter, although manual adjustment is also available.
However, for the easiest setup, follow these steps
while seated in the listening position that will be used
most often:
1. Make certain that all speaker positions have been
properly configured for their “large” or “small” set-
tings (as outlined above) and turn off the OSD
system if it is in use.
2. Adjust the volume so that it is at
-15dB,as
shown in the on-screen display or
Lower
Display Line
¯.
3. Hold the remote in front of you at arm’s length,
being sure not to cover the
EzSet Sensor
Microphone
at the top of the remote.
4. Press and hold the
SPL Selector Button for
three seconds. Release it when the
Program/
SPL Indicator
c stops flashing and remains
lit. Within five seconds, press the
5 Button r
on the remote if your system is configured for
5.1 operation with standard speakers or the
7 Button r on the remote if your system is
configured for 6.1/7.1 operation with one or two
rear surround speakers. Once the correct channel
configuration button has been pressed, the test
noise will be heard from the front left speaker.
5. At this point, EzSet will take over, adjusting the
output level of each channel so that when the
process is complete all levels will be equal and at
the set reference point. This process may take a
few minutes, depending on the extent of adjust-
ment required.
40
43
35
* DELAY ADJUST *
FRONT :10FT
CENTER :10FT
SURROUND :10FT
SURR BACK :10FT
UNIT :FEET
BACK TO MASTER MENU