Filter
Top Products
32
Outlaw Audio
Owner’s Manual
33
Model 950 7.1 Channel Preamp/Processor
Owner’s Manual
Tuner Operation
The Model 950 Tuner can receive AM, FM and FM stereo broadcasts. Up to 32
stations can be preset and accessed from the front panel or remote. Stations
can also be tuned manually.
NOTE: Tuner reception cannot take place unless an appropriate AM and/or FM
antenna is connected to the rear panel of the 950 as described on page 20.
To operate the tuner:
1. Press the AM/FM button on the remote control once, or press either
SOURCE button on the front panel until the display shows:
TUNER 01-S STEREO
FM 100.1 MHz -10dB
This indicates that the Tuner is in FM, with Stereo selected as the Sur-
round mode. The number displayed next to the Tuner text is the Preset
number currently selected or last selected, followed by the Stereo recep-
tion indicator if the station is being received in stereo. The numbers next
to the FM text are the frequency of the selected preset or station . The
numbers in front of the dB indication are the current volume setting.
2. Press the AM/FM button on the remote control or the front panel
to change between AM and FM bands.
TUNER 01 STEREO
AM 1000KHz -10dB
This display indicates that the Tuner is in AM with a selected preset and
the frequency of that preset or station. The numbers in front of the dB
indication are the current volume setting.
3. Use the and TUNE buttons on the front panel or the remote
to change the tuner frequency.
The new frequency will be displayed to the left of the volume level on
the Front Panel Display and OSD.
TUNER 01-S STEREO
FM 95.5 MHz -10dB
Pressing a TUNE button once increases or decreases the FM frequency
by .1 MHz and the AM frequency by 10 KHz.
4. Press and hold either the and TUNE buttons on the front panel
or the remote to scan continuously up or down the selected band.
The tuner will stop on the next available station when you release
the button.
5. Press the T.MODE button on the remote or the FM MODE button
on the front panel to toggle between Stereo and Mono.
If an FM station produces lots of noise or sound that cuts in and out
while in stereo, use this control to change the FM mode from Stereo
to Mono.
If you select Mono as the operating mode an indicator will appear next
to the preset number and the display will show:
TUNER 01-M STEREO
FM 95.5 MHz -10dB
To preset a radio station into memory:
1. Tune to the radio station you desire.
2. Press and hold the MEM button on the remote or the MEMORY
button on the front panel to store a station into a preset location.
The display will change to show the word Memory along with a ashing
number as shown below:
MEMORY 01-S STEREO
FM 99.9 MHz -10dB
3. Quickly enter the desired preset/memory location (01 through 32)
using the numeric keypad on the remote.
This programs the radio station to that memory location. You have
approximately 5 seconds to enter a number.
PRESET 01-S STEREO
FM 99.9 MHz -10dB
Up to 32 stations can be stored, randomly between AM and FM, in
memory as presets.
To tune to a radio station that you have preset:
1. Set the Model 950 to Tuner.
2. Use the numeric keypad on the remote control to enter the 2-digit
number of the preset that you want to hear.
The tuner frequency (and band if it is different then the previously tuned
station) changes to the new station in the preset memory of the 950.
To change a preset radio station:
1. Tune to the new radio station you desire.
2. Press and hold the MEM button on the remote or the MEMORY
button on the front panel.
The display will change to show the word Memory along with a ash-
ing number.
3. Quickly enter the new preset/memory location (01 through 32)
using the numeric keypad on the remote.
This replaces the previously memorized preset with your new selection.
You have approximately 5 seconds to enter a number.
MEMORY 01-S STEREO
FM 106.7 MHz -10dB
Operation