Filter
Top Products
6
ENGLISH
ON / STANDBY
B
PERSONAL COMPONENT SYSTEM / STEREO CASSETTE TAPE DECK DRR-F100
REC/
REC MUTE
CD SRS
COUNTER
RESET
DOLBY NR
REC LEVEL
OPEN / CLOSE
REV. MODE
-10
+5
+3+10-1-3-5-10
-20
-30-40
dB
L
R
TAPE
B
PLAY
MIN
MAX
PHONES
BASS
TREBLE
BALANCE
LR
SYSTEM
REMOTE SENSOR
VOLUME
ON / STANDBY
PERSONAL COMPONENT SYSTEM / AM-FM STEREO RECEIVER DRA-F100
RT
EON-PTY
EON-TA
B
MHz
TUNED STEREO AUTO
CH
TIMER
MONO /
STEREO
BAND
MEMORY
FUNCTION
UP
DOWN
TUNING
TIMER
DISPLAY
ON / STANDBY
OPEN/CLOSE
PERSONAL COMPONENT SYSTEM / COMPACT DISC PLAYER DCD-F100
/ /
3
B
POWER LOADING MECHANISM
ON / STANDBY
B
EJECT
PERSONAL COMPONENT SYSTEM / MINIDISC RECORDER DMD-F100
INPUT SELECT
DIGITAL
ANALOG
12
REMOTE SENSOR
RANDOM
-60 -40 -30 -20 -12 -6 -2 0
OVER
L
dB
R
1
D.IN
04Tr 12m 48s
13
EDIT
-
+
PUSH ENTER
REC LEVEL
CHARACTER
REC /
PICK REC
CD SRS
PICK REC MODE
12
CONNECTOR
SYSTEM
OPTICAL
DIGITAL OUT
LINE OUT
L
R
PHONO AUX CD PB-TAPE-REC PB-MD-REC
12
CONNECTOR
SYSTEM
L
L
R
R
R L
SPEAKERS
IMPEDANCE 4~16º
FM COAX 75º LOOP
ANT.
AM
AC OUTLET
SWITCHED
120W(1A.)MAX
120V 60Hz
AC OUTLET
UNSWITCHED
120W(1A.)MAX
120V 60Hz
SIGNAL GND
R
L
R
L
OUTPUT INPUT
R
L
R
L
OUTPUT INPUT
OPTICAL
4
CONNECTIONS
This system includes digital circuitry which may
cause interference such as color blotching or
changes in the color on TVs. If this happens,
move the system and the TV as far apart as
possible.
NOTE:
System operations
Such system operations as the timer and the auto on functions,
as well as remote control operations cannot be performed
unless all the RCA pin-plug cords and system connector cords
are connected between the units, so be sure to make all the
connections properly as shown in the diagram. Also,
disconnecting system connectors while the system is operating
may result in malfunction. Be sure to unplug the power cord
before changing connections.
AM loop
antenna
FM
antenna
Record player
Speaker systems
Use a record player with
an MM cartridge.
• Disconnect the ground cord if
humming or noise is produced
when it is connected.
Ground cord
LD player, video deck, etc.
Power plug
AC 120 V 60 Hz
(Plug into a power outlet)
• Do not plug the power cord into the power outlet until all connections are completed. Be
sure to interconnect the channels (L to L (white) and R to R (red)) properly, as shown on the
diagram.
• Insert the plugs securely. Incomplete connections may result in noise.
• Be sure to connect the speaker cords between the speaker terminals and the speaker
systems with the same polarities (+ to +, – to –). If the polarities are switched, the sound at
the center will be weak, the position of the different instruments will be unclear, and the
stereo effect will be lost.
• After unplugging the power cord, wait about 5 seconds before plugging it back in.
• Note that setting the connection cords (pin-plug cords) next to the power cords may result
in humming or other noise.
NOTES:
AM-FM Stereo Receiver
(DRA-F100)
CD player
(DCD-F100)
Connecting the speaker systems
Connect the speaker system for the
left channel (the left side as seen
from the front) to the ”L“ terminals,
the speaker system for the right
channel to the ”R“ terminals. Be sure
to use speaker systems with an
impedance of 4 Ω/ohms or greater.
Whenever the power switch is
in the STANDBY position, the
unit is still connected on AC line
voltage.
Please be sure to unplug the
cord when you leave home for,
say, a vacation.
CAUTION:
Right Left
AC Outlets
• SWITCHED outlet (DRA-F100)
The power of this outlet is switched on and off by the receiver’s SYSTEM
power operation switch.
This outlet will also be switched on when the power is set to ON-
STANDBY with the remote control.
When the receiver is in the standby mode, the outlet switches off after
approximately 20 seconds.
• UNSWITCHED outlets (DCD-F100)
These outlets remains on at all times, regardless of the setting of the CD
player’s and cassette’s power operation switch.
✽ Do not connect the receiver’s AC cord to the outlets on the CD player
(DCD-F100). Doing so could result in damage.
PRECAUTIONS FOR
INSTALLATION
For heat dispersal, leave at least
10 cm of space between the
top, back and sides of this unit
and the wall or other
components.
Stacking installation
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article
820-40 of the NEC which provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
Connecting a MD recorder
Connections for recording:
Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s tape recording
(OUT) jacks using pin plug cords.
Connections for playback:
Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s tape playback
(IN) jacks using pin plug cords.
MD recorder
Connecting a tape deck
Connections for recording:
Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s tape recording
(REC) jacks using pin plug cords.
Connections for playback:
Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s tape playback
(PB) jacks using pin plug cords.
Tape deck