Denon DN-D4500 CD Player User Manual


 
9
ENGLISH
q
i
eyo
w
u
tr
!0
(5) Display
q
Track, minute, second and frame
displays
These displays indicate current position
information.
w
Loop mode indicators
DN-D4500 has Loop mode indicators consist of
two sets of A (A1, A2), B and two arrows. A
and B marks indicate A and B points are set.
•Two arrows indicate loop setting mode as
follows.
Example: A1 B
Both arrows on:
Seamless Loop mode
, Both arrows flashing:
Seamless Loop Playing
,
Left arrow on, right flashing:
Exit play from Seamless Loop
e
Time mode indicators
When the TIME/TOTAL button is pushed, the
Time mode indicator switches as follows:
ELAPSED:
Track’s elapsed time is displayed.
REMAIN:
Track’s remaining time is displayed.
T. + ELAPSED:
The total elapsed time of disc or
programmed track is displayed.
T. + REMAIN:
The total remaining time of disc or
programmed track is displayed.
BA1
BA1
BA1
BA1
BA1
r
MP3 file search mode indicator
FILE:
FILE indicator appears in display, when in
the FILE name search mode.
FOLDER:
FOLDER indicator appears in display, when
in the FILE & FOLDER name search mode.
TITLE:
TITLE indicator appears in display, when in
the TITLE name search mode.
ARTIST:
ARTIST indicator appears in display, when in
the ARTIST name search mode.
t
Character display
This displays various operational information,
text message, etc.
y
Play mode indicators
When SINGLE indicator lights up, playback will
finish at end of current track.
When CONT. indicator lights up, playback
continues to the end of the disc.
u
MEMO indicator
MEMO sign appears in display when there is a
memory setting for the currently playing track
or the track at which the standby mode is
currently set.
@9
Control connector
Connect the opposite side of supplied 8pin din
cable to the DN-D4500 (main unit).
(4) RC-D45 Rear panel
(3) DN-D4500 Rear panel
@5
Analog output jacks 1, 2
(ANALOG OUT 1, 2)
These are unbalanced output jacks. The audio
signals from the both players are output from
these jacks.
@6
Digital output jacks 1, 2
(DIGITAL OUT 1, 2)
Digital data is available from this jack.
Use 75 /ohms pin cord for connection.
•We recommend you use braided wire type
shielded cable.
NOTE: The playback level after analog
conversion is set to –6dB bellow the
usual level to avoid digital distortion.
@7
Fader input jacks 1, 2 (FADER 1, 2)
Use this when your mixer has Fader Start
function with 3.5 mm stereo mini cord.
@8
Remote control connector
(REMOTE)
Connect the supplied 8pin din cable to the
RC-D45 control unit.
!9
FLIP/B TRIM button
Push this button to switch between the loop
mode/hot start mode and stutter mode.
After setting the B point, the B TRIM MODE
can be selected.
@0
A1, A2 buttons
Push these buttons to set the start point for
loop playback (point A-1 or A-2).
Push these buttons to use the stutter and hot
start functions.
@1
B button
Push this button to set the end point for loop
playback (point B).
@2
EXIT/RELOOP button
When this button is pushed during a seamless
loop, the track resumes back to normal play
from the B point. (EXIT)
When pushed again, the playback jumps back
into your A-B seamless loop. (RELOOP)
@3
TITLE button
CD TEXT:
When there is CD text data, the CD text data is
displayed automatically or when the button is
pressed.
If no TEXT is available, the display will indicate
“No TEXT”.
MP3:
When an MP3 file has ID-3 tag data, the title,
artist name and album name can be selected
and displayed each time the button is pressed.
@4
MEMO, PRESET button
MEMO:
The memo mode starts when this button is
pushed once in the CUE mode.
PRESET:
When this button is pushed for more than 1
sec, the PRESET mode starts.
NOTE:
Memo’s can not be set for MP3 files.