Filter
Top Products
14
ENGLISH
2. Disc tray auto close
1
Disc tray will automatically close after 30
seconds have elapsed for the disc tray auto
close mode. (Preset item 3)
3. End of message
1
During playback, the Play Position indicators
start flashing when the remaining playing
time to the end of the track (set in the preset
mode)is reached, indicating that the end of
the track is near. (Preset item 6)
4. Power on play
1
When “Power On Play”is set to “ON” mode at
“⁄1 PRESET (8)”, playback starts from the first
track on the disc when the power is turned on.
1. Relay play
• The unit can play CD1 and CD2 alternately.
• The relay mode is set when the CONT./SINGLE
button u is pressed for over 1 second.
(1) Single relay mode
1
Press the CONT./SINGLE button
u several times until “SINGLE”
indicator flashes on the display.
• When playback is finish of the
desired track, the opposite
drive will start to play.
• When both CD1 and CD2 set to the SINGLE
RELAY mode, endless play is available for
the each track of CD1 and CD2 alternately.
(2) Continuous relay mode
1
Press the CONT./SINGLE button u
several times until “CONTINUOUS”
indicator flashes on the display.
• When playback is finish for the
final track on the target disc,
the opposite drive will start to
play.
• When both CD1 and CD2 set to the
CONTINUOUS RELAY mode, endless play is
available for each disc of CD1 and CD2
alternately.
10
MEMO (Custom Setting Memory)
CD setting information can be stored in the non-volatile memory. The stored information can be called out of the
memory later, making it easy to prepare for your mixing.
NOTE: The MEMO function cannot be used for MP3.
1. About TRACK MEMO
• Up to 1000 memo points can be stored to internal memory for later recall.
The number of tracks on a particular CD only limits the amount of memo points available per that disc.
Example: If your CD has 22 tracks, you can only save up to 22 memos. (1 memo group per track.)
CAUTION:
1000 is the maximum possible number of tracks that can be stored to memory.
However, to simplify the MEMO operations, the memory system manages each 200 MEMO data groups
as a minimum unit (the total 1000 memory capacity divided into 5 memory data groups). When you want
to clear just one MEMO data in the 1 MEMO CLEAR mode (see page 15), the unit will erase the memo
information but not the internal memo allocation number. Accordingly, depending on conditions, the
number of tracks that can be stored in the memory may be fewer than 1000.
Once you reached 1000 stored points, you will see a message that says “MEMO FULL!”. At this time you
will need to “delete” old data to make room for new memo points. Therefore the oldest 200 memo points
in that group will be deleted and become available.
• The MEMO indicator on the display lights up when a track for which data is stored in the memory is
selected.
2. MEMO ITEMS
The following items are max to be stored under 1 memory bank:
q CUE point.
w A1 and B1 points, A2 and B2 points.
e Playing pitch, pitch range pitch on/off, Key Adjust on/off, Hot Start/Stutter setting.
3. MEMO MODE SELECT
q Push the MEMO button @4 in CUE mode to enter MEMO mode.
w Turn the TRACK SELECT knob o to select the various MEMO modes from as follows.
Memo Set, MemoCall, Memo Clr
Depending on conditions, some modes cannot be selected.
e Push the MEMO button @4 again to exit MEMO mode.
(1) Storing data in the memory [Memo Set]
• After making your desired settings to be stored in memory, then push CUE button !0.
• In CUE mode, push MEMO button @4 once to enable Memo set function.
• If the MEMO indicator is already lit up, it is necessary to clear existing Memo before storing a new
Memo.
• At last push TRACK SELECT knob o down to save. You can see “Complete!” message and MEMO
indicator lights up.
MEMO FULL
• If the memory is full and no more data can be stored, “Memo Full!” and “Del. 200?” message appears.
• In this case, you need to clear memory of First 200s Memo (number 1 to 200) at a time to make space
for new memos.
•To make space, push TRACK SELECT knob o down while “Del. 200?” message is displayed.
• “Delete OK?” message appears then push TRACK SELECT knob o down again to execute clearing.
•After the first 200s Memo (number 0 to 199) are cleared, number after 200 Memo are renumbered as
new 1, 2, 3…(now you have a new set of 200 empty spaces.).
9
OTHER FUNCTIONS
Manual search
For only C.B.R files, manual searching can be performed.
NOTE:
•With manual searching, it is only possible to
search within the selected file.
•Manual searching in the reverse direction is
possible up to the point 5 seconds before the point
at which searching starts.
•The searching speed may vary according to the
file’s compression rate, etc.
•V.B.R. is not supported with this function.
Seamless Loop/Hot start/Stutter/BTrim
For only C.B.R. files, Hot starting, seamless loop
playback, stuttering and B trim can be performed in
the same way as with normal CDs.
NOTE:
•The A and B points for the seamless loop must
both be set within the same file.
•V.B.R. is not supported with these functions.
BRAKE
BRAKE is supported in the same way as with normal
CDs.