Filter
Top Products
35
System call
(1)System call buttons
The buttons that can be used for the system call function are
shown on the diagram at the right.
System call signals can be stored at different buttons according to
the mode. System call signals can be stored at a maximum of 6
buttons other than the CALL 1 and CALL 2 buttons.
29 successive operations can be set at each of these buttons.
1
2
3
456
789
+10
0
TV/
VCR
OFF
TV
CD
CDR/MD/TAPERECEIVER
VCR DBS/CABLE
SKIP
SKIP
ENTER
MEMORY
VOLUME
CHANNEL
+
-
+
-
VDP DVD
POWER
REMOTE CONTROL UNIT
RC-883
ON /
SOURCE
TUNER
VDP
VCR-1 VCR-2/V.AUX
DVD
TV/DBS
CDR/TAPE
PHONO
CD
SURROUND
INPUT
OUTPUT
TEST
TONE
SPEAKER
6.1 / 7.1
SURROUND
5CH / 7CH
ANALOG
EXT.INMODE
CALL 2
BACKLIGHT
CALL 1
STEREO
STEREO
DOLBY/DTS
SURROUND
DSP
SIMU.
DISPLAY
SYSTEM CALL
DIRECT
RETURN
SETUP
MENU
SHIFT
SURR.
PARA.
OSD
A/B
MUTING
BAND MODE
TUNING
TUNING
(2)Storing system call signals
1
2
3
4
ON /
SOURCE
OFF
ENTER
SHIFT
BAND MODE
TUNING
TUNING
ENTER
SHIFT
Press the power ON/SOURCE button and the OFF button at
the same time. “SET UP” appears on the remote control
unit’s display.
Press the ENTER button.
Use the D and H cursor buttons to display “SYS CALL” on the
remote control unit, then press the ENTER button.
• Display “SYS MODE” on the remote control unit’s display.
When “SYS MODE” is displayed, the remote control unit’s
display switches as shown below each time the D and H
cursor buttons are pressed.
When “SYS CALL 1” or “SYS CALL 2” is selected, the
signals are stored at the SYSTEM CALL 1 and CALL 2 buttons
(green), regardless of the mode. When the enter button is
pressed, the button registering mode (step 6) is set.
To register at other buttons, select “SYS MODE” then press
the enter button.
• After “SEL MODE” is displayed on the remote control
unit’s display, the mode last set is displayed.
1
2
3
456
789
+10
0
TV/
VCR
OFF
TV
CD
CDR/MD/ TAPE RECEIVER
VCR DBS/CABLE
SKIP
SKIP
ENTER
MEMORY
VOLUME
CHANNEL
+
-
+
-
VDP DVD
POWER
REMOTE CONTROL UNIT
RC-883
ON /
SOURCE
TUNER
VDP
VCR-1 VCR-2/V.AUX
DVD
TV/DBS
CDR/TAPE
PHONO
CD
SURROUND
INPUT
OUTPUT
TEST
TONE
SPEAKER
6.1 / 7.1
SURROUND
5CH / 7CH
ANALOG
EXT.INMODE
CALL 2
BACKLIGHT
CALL 1
STEREO
STEREO
DOLBY/DTS
SURROUND
DSP
SIMU.
DISPLAY
SYSTEM CALL
DIRECT
RETURN
SETUP
MENU
SHIFT
SURR.
PARA.
OSD
A/B
MUTING
BAND MODE
TUNING
TUNING
1
7
3, 4, 5
2, 3, 5, 6, 8
The included remote control unit is equipped with a system call function allowing a series of remote control signals to be transmitted by pressing
a single button.
This function can be used for example to turn on the amplifier’s power, select the input source, turn on the monitor TV’s power, turn on the source
component’s power and set the source to the play mode, all at the touch of a button.
SYS MODE SYS CALL 1
SYS CALL 2
BAND MODE
TUNING
TUNING