Denon AVR-1082 Stereo System User Manual


 
14
ENGLISH
Use the CURSOR buttons to adjust all the speakers to the
same volume.
The volume can be adjusted between 12 dB and +12 dB in
units of 1 dB.
Example: When the volume is set to
12 dB while the test tone
is being produced from the
subwoofer
FL C FR SR SBR SBL SL SW
SB
1spkr
2spkrs
When the surround back speaker setting is set to
1spkr for Speaker Configuration, this is set to SB.
7
Select Ye s.
BAND MODE
TUNING
TUNING
8
a. If the Auto mode is selected:
Test tones are automatically emitted from the different
speakers.
The test tones are emitted from the different speakers in
the following order, at 4-second intervals the first time and
second time around, 2-second intervals the third time
around and on:
BAND MODE
TUNING
TUNING
Flashing
Example: When the volume is set to
12 dB while the
subwoofer is selected
b. When the Manual mode is selected
Use the CURSOR left and right to select the speaker for
which you want to output test tones, then use the
CURSOR up and down to adjust so that the volume of the
test tones from the various speakers is the same.
Flashing
BAND MODE
TUNING
TUNING
9
After the above settings are completed, press the ENTER button.
The Channel Level screen reappears.
ENTER
SHIFT
BAND MODE
TUNING
TUNING
To cancel the settings, select Level Clear and Ye s on the Channel Level screen, then make the
settings again.
The level of each channel should be adjusted to 75 dB (C-weighted, slow meter mode) on a sound level meter
at the listening position.
If a sound level meter is not available adjust the channels by ear so the sound levels are the same. Because
adjusting the subwoofer level test tone by ear is difficult, use a well known music selection and adjust for natural
balance.
NOTE: When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofers
own volume control.
When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel
level adjustments made will affect ALL surround modes. Consider this mode a Master Channel Level
adjustment mode.
After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the
individual surround modes and adjust channel levels that will be remembered for each of those modes.
Then, whenever you activate a particular surround sound mode, your preferred channel level adjustments
for just that mode will be recalled. Check the instructions for adjusting channel levels within each
surround mode on page 27.
You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5/7 CH
STEREO, DOLBY/DTS SURROUND, WIDE SCREEN, ROCK ARENA, JAZZ CLUB, VIDEO GAME, MONO
MOVIE, and MATRIX.
When using either surround speakers A or B, or when using surround speakers A and B at the same time,
be sure to adjust the balance of playback levels between each channel for the various selections of A
or B and A and B.
This setting assigns the digital input jacks of the AVR-3802 for the different input sources.
Setting the Digital In Assignment
1
At the System Setup Menu select Digital In Assignment.
BAND MODE
TUNING
TUNING
2
Switch to the Digital In Assignment screen.
ENTER
SHIFT
3
Select the digital input jack to be assigned to the input source.
To select the input source
To select the digital input jack
Select OFF for input sources for which no digital input jacks are used.
If Yes is selected for Default, the settings are automatically reset
to the default values.
BAND MODE
TUNING
TUNING
BAND MODE
TUNING
TUNING
NOTES:
The OPTICAL 3 jacks on the AVR-3802s rear panel are equipped with an optical digital output jack for
recording digital signals on a CD recorder, MD recorder or other digital recorder. Use this for digital recording
between a digital audio source (stereo - 2 channel) and a digital audio recorder.
Do not connect the output of the component connected to the OPTICAL 3 OUT jack on the AVR-3802s rear
panel to any jack other than the OPTICAL 3 IN jack.
•“PHONO and TUNER cannot be selected on the Digital In Assignment screen.
4
Enter the setting.
The System Setup Menu reappears.
ENTER
SHIFT