Filter
Top Products
11
ENGLISH
1 4,6
PHONES
BASS
TREBLE
BALANCE
LR
SYSTEM
REMOTE SENSOR
VOLUME
ON / STANDBY
PERSONAL COMPONENT SYSTEM / AM-FM STEREO RECEIVER DRA-F100
B
MHz
TUNED STEREO AUTO
CH
TIMER
MONO /
STEREO
BAND
MEMORY
FUNCTION
UP
DOWN
TUNING
TIMER
DISPLAY
3,5 2
7
LISTENING TO RADIO PROGRAMS
(Check the connections on pages 5 and 6.)
Receiver
(DRA-F100)
TUNING
Example: Tuning in FM 87.5 MHz
(AM stations are tuned in using the same procedure.)
1
Set the VOLUME control on the
receiver to the minimum position,
then press the SYSTEM power
operation switch (SYSTEM ON/
STANDBY) to turn on the power.
SYSTEM
ON / STANDBY
2
Press the BAND button on the
receiver to select the FM band.
BAND
MHz
3
Use the TUNING UP and DOWN
buttons to tune the frequency to
87.50. Once the frequency is tuned
in, adjust the volume to the desired
level using the VOLUME control.
DOWN
TUNING
UP
DOWN
TUNING
UP
TUNED STEREO
MHz
AUTO
Auto Tuning
• When one of the TUNING buttons is pressed, the frequency changes in steps of 50kHz in the FM band, 9kHz in the AM band.
• If one of the TUNING buttons is held in for over 1 second, the frequency continues to change when the button is released (auto
tuning) and stops when a station is tuned in. Tuning will not stop at stations whose reception is poor.
• To stop the auto tuning function, press the UP or DOWN button once.
Example: Presetting FM 87.5 (currently tuned in) at preset number 3
Presetting AM and FM Stations
4
Press the MEMORY button.
The indicator flashes for
10 seconds.
MEMO
MEMORY
TUNED STEREO AUTO MEMO
CHMHz
5
Use the TUNING UP and DOWN
buttons to call out the number at
which you want to preset the
station (3), or simply press the
corresponding number button “3”
on the remote control unit.
TUNED STEREO AUTO MEMO
CHMHz
6
Press the MEMORY button while
the indicator is flashing.
MEMO
MEMORY
TUNED STEREO AUTO
CHMHz
Up to 40 AM or FM stations can be preset using this procedure.
(FM ONLY)
This function automatically stores the FM stations which can be received in the area in which the set is being used in the
preset memory. Also note that the channel memories can be changed at will even after the preset stations have been
stored with this function.
Auto Preset Memory Function
The preset stations can be recalled using the number buttons on the remote control unit.
Also, if the following operation is performed when the system power is off, the power automatically turns on and the radio
is played. (Auto on function)
Listening to Preset Stations
Flashes
Flashes
Flashes
“P3” lights
“P” flashes
1
Connect the FM antenna and set it
so that FM stations can be
received.
2
Press the SYSTEM power operation
switch (SYSTEM ON/STANDBY) to
turn on the power while holding in
the MEMORY button.
MEMORY
SYSTEM
ON / STANDBY
POWER
SLEEP
EDIT
RANDOM REPEAT
RESET
REC / MUTE
TIME
SIDE A/B
PROGRAMCANCEL DIRECT FUNCTION
1 2 3 4 5
89
8
9
2
2
1
2
1
6
7
6
7
01
DECK
CD
MD
TUNER
q
w
MEMO
3
Searching begins automatically, and
stations are stored in the preset
memory in order, beginning from
channel 1 (The operation
automatically stops once 40
stations have been set in the
memory.)
TUNED STEREO AUTO
CHMHz
TUNED STEREO AUTO
CHMHz
Refer to page 5.
1
2
Press the TUNER button on the
remote control unit.
Press button ”3“ on the remote
control unit.
”AUTO“ is displayed and the MEMO indicator
flashes during this operation.
When the operation is completed, the station
stored at preset number 1 is tuned in.
NOTES:
• In addition to the reception frequency, the reception mode (monaural or auto) is also preset, so check the display when
presetting stations.
• If a station is preset at a number where a station is already preset, the previous station is replaced with the new station.
• The preset memory is not cleared immediately when the power cord is unplugged, but is cleared if the cord is left
unplugged for an extended period of time. If this happens, preset the stations again.
This lights when a station is tuned in.
Example: Listening to the station preset at number 3
(This operation is only possible from the remote control unit.)