Filter
Top Products
42
Getting Started
Connections Remote Control Information Troubleshooting
Specifications
ENGLISH
Settings
Adjusting the Sound Field Effect (Parameter)
Setting items Setting contents
Dynamic EQ
Audyssey Dynamic EQ solves
the problem of deteriorating
sound quality as volume is
decreased by taking into
account human perception
and room acoustics.
This can be set when the
“MultEQ” (vpage 41)
is set to anything other
than “OFF”.
ON : Use Dynamic EQ function.
OFF : Do not use Dynamic EQ function.
• When set to “ON”, “ ” is displayed.
• When “MultEQ” is set to “OFF”, “Dynamic EQ” is automatically set
to “OFF”
• This can also be set by pressing .
Dynamic EQ : ON/Volume : OFF
“Green” “OFF”
Dynamic EQ / Volume : OFF
NOTE
“Tone Control” is set to “OFF” when “Dynamic EQ” is set to “ON”.
Reference Level Offset : Audyssey Dynamic EQ takes the standard film
mixing level of 85 dB SPL during –20 dB FS input as its reference level.
However, since standardization is lacking outside the film industry, the
reference level of media contents may not be appropriate. In order to
view such contents, Reference Level Offset of Dynamic EQ has available
offsets of 5 dB, 10 dB and 15 dB.
0dB : Suitable for viewing movies.
5dB : Suitable for listening to classical music and other content mixed
at a high level.
10dB : Suitable for listening to jazz and other audio sources with a wide
dynamic range. Also suitable for viewing TV.
15dB : Suitable for listening to pop, rock music and other content with an
extremely wide dynamic range.
Setting is enabled when “Dynamic EQ” is “ON”.
•
•
•
•
Dynamic Volume
Audyssey Dynamic Volume
solves the problem of
large variations in volume
level between television
programs, commercials, and
between the soft and loud
passages of movies.
This can be set when
“Dynamic EQ” (vpage
42) is set to “ON”.
ON : Use Dynamic Volume. The Dynamic Volume effect will be at the level
of the “Setting” (vpage 42)
OFF : Do not use Dynamic Volume.
• When set to “ON”, “ ” is displayed.
• When “MultEQ” is set to “OFF”, “Dynamic Volume” is automatically
set to “OFF”.
• This can also be set by pressing .
Dynamic EQ / Volume : ON
“Green” “Red”
Dynamic EQ : ON / Volume : OFF
“Green” “Red”
“Red” “Off”
Setting items Setting contents
Adjust CH
Adjust the tonal quality of
the individual speakers.
1. Select speaker adjustment method.
All CH : Adjust tonal quality for all speakers together.
L/R CH : Adjust tonal quality for each L/R speaker pair.
Each CH : Adjust tonal quality for each speaker separately.
2. Select the frequency band to be adjusted.
63Hz / 125Hz / 250Hz / 500Hz / 1kHz / 2kHz / 4kHz / 8kHz /
16kHz
b When “L/R CH” or “Each CH” is selected, select the speaker to be
adjusted.
3. Adjust the level.
–20.0dB ~ +6.0dB (0dB)
Base Curve Copy
Copy the MultEQ “Audyssey
Flat” correction curve.
Yes : Copy.
No : Do not copy.
“Base Curve Copy” is displayed after the Audyssey Auto Setup
procedure has been performed.
Default
Reset the “Manual EQ”
settings to their defaults.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
Adjust tonal quality for each speaker using graphic equalizer
(Manual EQ)
Default settings are underlined.
Setting items Setting contents
Setting
Set Dynamic Volume effect.
This can be set when
“Dynamic EQ” (vpage
42) is set to “ON”.
Day : Low setting provides the least adjustments to the loudest and
softest of sounds.
Evening : Middle setting prevents loud and soft sounds from being much
louder and softer respectively than average sounds.
Midnight : High setting affects volume the most, causing all sounds to be
of equal loudness.
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
Remote control
operation buttons
:
Displaying the menu
Cancel the menu
Playback