Filter
Top Products
7
In FM band
Preset channel_2
loaded
Preset “PS+”
to target preset
channel
In FM band with preset channel
In FM band without preset channel
press “PROG”
enter to PRESET
SETTING mode
press “PROG”
Channel number
selection
press “PS+/PS-”
to a desired
channel number
end of prest
press
“PROG”
Signal
FLAT
ROCK
Jazz
CLASSIC
POP
16
Radio
Load Preset Channel
Load up and down correspond to “PS+” and “PS-”
key, respectively.
A Press “PS+” or “PS-“ to recall preset channel
Notes: 1) the current display frequency will not be
kept during above operation.
Save Preset
Channel number select up or down correspond to
“PS+” and “PS-” key, respectively.
a) In TUNER mode, choose a station that you want
to save. Press “PROG” to enter programming
mode.(--) will flash.
b) Press “PS+” or “PS-“ to desired preset number
(e.g. channel-10).
c) Press “PROG” to save that station.
d) Repeat above procedure.
Notes: 1) The original preset of channel-2 will not
be changed during above operation.
Mono/Stereo
A Press “MO/ST” to toggle the type of FM signal.
Notes: 1. Only for FM band
2. If stereo signal is too weak, ‘STEREO’
icon will not appear. Press this key
change to Mono mode. The reception
may be improved.
A high-pitched noise called BEAT is sometime heard
during reception of radio broadcast.
A Press “SIGNAL”
until find a best
quality of signal.
In FM band
(Current mode
=Stereo)
Change to
MONO mode
press “MO/ST”
press “MO/ST”
In FM band
choose 1st
method
press”Signal”
choose 2nd
method
press”Signal”
choose best sound
quality after 3sec
waiting
Electronic volume control display
Equalizer “ROCK”
Function Select
1 Press the “TUNER/BAND” button to enable the
AM/ FM tuning function. When in TUNER mode,
the LCD will display the band (AM/FM), and the
station frequency.
2 Press the “CD” button to set to CD mode. When
first set to CD mode, the display will search for
CD and track information.
3 Press the “PHONO” button to set to PHONO
mode. When in PHONO mode, the display will
read “PHONO”.
4 Press the “TAPE” button to set to CASSETTE
mode. The display will read “COUNTER” when
in cassette mode.
Equalizer
1 This unit has a built in equalizer. The equalizer
fine tunes the sound according to the type of
music you like. Pressing the EQ button results
in the following changes:
Basic Operation
Functions (cont.)
Powering Up Your Crosley
Your new Crosley is equipped with a POWER /
STANDBY button. Press the POWER / STANDBY
button on either the front of the unit or on your remote
control. The Standby light will turn from red to green.
When turned off, the standby light will turn red.
During standby mode, all presets will remain
programmed in your unit.
Functions
Electronic Volume Control
1 Press the “VOL+” button to increase the volume.
The volume level will be shown in the LCD
display.
Note: Volume range for this units start at level
0 and end at level 40.
2 Press the “VOL-” button to decrease the volume.
3 Press and hold either the “VOL+” or the
“VOL-” button to continuously increase or
decrease the volume. The volume will continue
to increase or decrease until the button is
released.
4 Press the “MUTE” button to set the volume to
0.
Press the “MUTE” button again to return to the
previous volume level.
Receiving tuning frequency display
PHONO display
After reading display
CD TOC reading display
TAPE mode display