Filter
Top Products
280-8046-00
DXZ746MP 23
English
Dimmer level
You can adjust the reduced illumination level of
the dimmer.
∗ The factory default setting is “LV3”.
(Adjustment range is LV1 to LV5)
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [a] or [d] button to select the
“
ÅÅ
ÅÅ
Å
DIMMER LV
ÎÎ
ÎÎ
Î
”.
3. Turn the [ROTARY] knob clockwise or coun-
terclockwise to adjust the reduced illumina-
tion level of the dimmer.
● LV1 to LV5:
The dimmer operation is performed depend-
ing on the set level LV1 to LV5.
● OFF:
No dimmer operation is performed.
4. Press the [T] button to return to the previous
mode.
Adjusting the display contrast
You can adjust the display contrast to match the
angle of installation of the unit.
∗ The factory default setting is “8”. (Adjustment level:
1 to 18)
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [a] or [d] button to select
“
ÅÅ
ÅÅ
Å
CONTRAST
ÎÎ
ÎÎ
Î
”.
3. Turn the [ROTARY] knob clockwise or coun-
terclockwise to adjust the contrast.
4. Press the [T] button to return to the previous
mode.
Anti-theft indicator
The red Anti-theft indicator is a function for pre-
venting theft. When the DCP is removed from
the unit, this indicator blinks.
∗ The factory default setting is “OFF”.
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [a] or [d] button and select
“
ÅÅ
ÅÅ
Å
BLINK LED
ÎÎ
ÎÎ
Î
”.
3. Turn the [ROTARY] knob clockwise to set
this function “ON” or turn it counterclockwise
to switch this function “OFF”.
4. Press the [T] button to return to the previous
mode.
Operations Common to Each Mode
Setting the Subwoofer
You can set the subwoofer on or off.
∗ The factory default setting is “ON”.
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [a] or [d] button and select
“
ÅÅ
ÅÅ
Å
SUB-W
ÎÎ
ÎÎ
Î
”.
3. Turn the [ROTARY] knob clockwise or coun-
terclockwise and select “ON” or “OFF”.
4. Press the [T] button to return to the previous
mode.
Setting LOW PASS FILTER
∗ The factory default setting is “THRGH” (Through).
∗ If subwoofer function is set “ON”, “LOW PASS FIL-
TER” can be selected.
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [a] or [d] button and select
“
ÅÅ
ÅÅ
Å
SUB-W LPF
ÎÎ
ÎÎ
Î
”.
3. Turn the [ROTARY] knob clockwise or coun-
terclockwise to select the setting. Each time
you turn the [ROTARY] knob, the setting
changes in the following order:
THRGH ➜ 50Hz ➜ 80Hz ➜ 120Hz
4. Press the [T] button to return to the previous
mode.
Setting the external amplifier
∗ The factory default setting is “OFF”.
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [a] or [d] button and select
“
ÅÅ
ÅÅ
Å
AMP-CANCL
ÎÎ
ÎÎ
Î
”.
3. Turn the [ROTARY] knob clockwise or coun-
terclockwise and select “ON” or “OFF”.
● ON:
Use with connected AMP.
● OFF:
Use with inside AMP.
4. Press the [T] button to return to the previous
mode.
03.12.26, 5:18 PMPage 23