Filter
Top Products
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
©American Audio® - www.americanaudio.us - MCD-810™ Instruction Manual Page 22
BASIC OPERATIONS (CONT.)
14. RECALL FLASH MEMORY:
The MCD-810 can store all your user programmed
cue points in to memory. These cue points may be
recalled at any time, even when a disc has been
removed and reloaded at a later time. To recall the
memory on a specific disc; 1) Be sure a CD is not
loaded in to the drive. 2) Press the MEMORY BUTTON
(12) so the blue memory L.E.D. turns on. 3) Insert the
CD. "RESTORING" will appear in the LCD (2) while
the memory is being installed and the blue MEMORY
BUTTON (12) L.E.D. will flash then turn off, when the
memory is loaded.
15. CLEAR ALL MEMORY:
You may clear the system memory at any time. This
will erase all your programmed memory and restore
the unit to it's default settings. There are two ways
to clear the memory; While main power is turned off,
turn the SEARCH KNOB (6) in a counter-clockwise
direction. While the search knob is turned in a coun
-
ter-clockwise direction turn main power on. Or, you
can press the TIME BUTTON until "PRESET MODE"
is displayed. Now turn the TRACK KNOB until "MEM
CLEAR" is displayed and then press the TRACK
KNOB and "ERASING" should be displayed.
13. SYSTEM MEMORY:
The MCD-810 comes with an incredible memory sys-
tem. The MCD-810™ can memorize virtually every
customized setting for a particular CD. The unit
can memorize all customized effect parameters, cue
points, and loops used on a particular disc. To store
all your setting for a CD, press and hold down the
MEMORY BUTTON (12) for at least one second. When
the memory has been stored properly the MEMORY
BUTTON L.E.D. will turn off.
Figure 26
Figure 27
Figure 25
16. FIRMWARE VERSION DISPLAY:
You may display the units firmware version. Firmware
is the units internal programming code. To view the
firmware version; Press the TIME BUTTON
for 2
sec. until "PRESET MODE" is displayed. Now turn
the TRACK KNOB until "VERSION" and the version
number is displayed in the LCD (2). Turning
and
pressing the TRACK KNOB can also select and set
Close Time Mode and Sleep Mode. Press the
TIME
BUTTON to exit Preset Mode.
Figure 28