Filter
Top Products
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
TAP
BOP
SGL
CTN
TIME
M
2
3 4
1
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
FOLDER
TRACK
M
TOTALREMAIN
S
F
PITCH
AUTOBPM
CD MP3
CUE
RELOOP
SINGLE
AUTOCUE
BASIC OPERATIONS (CONT.)
©American Audio® - www.americanaudio.us - MCD-810™ Instruction Manual Page 20
EXITING A LOOP - To exit a SEAMLESS LOOP,
press the OUT BUTTON (20)
. The IN BUTTON (21)
and OUT BUTTON (20) L.E.D.s will remain on, but
will stop flashing. Music playback will resume nor
-
mal play (Figure 20). The IN BUTTON (21)
and OUT
BUTTON (20)
L.E.D.s will remain on to remind you
that a loop is stored in memory.
Figure 20
REPLAY LOOP - The RELOOP (19) function
allows you to return to your stored loop at any time.
The
IN BUTTON (21) and OUT BUTTON (20) L.E.D.s
will indicate a loop is stored in memory, and may
be played at any time. To replay the loop, press the
RELOOP BUTTON (19)
. The IN BUTTON (21) and
OUT BUTTON (20) L.E.D.s will again begin to flash
indicating SEAMLESS LOOP mode has been acti
-
vated (Figure 21) and your stored loop will immedi
-
ately begin to play.
Stutter Effect: You can use your loop to create a
stutter effect. When a loop is playing press the IN
BUTTON (21)
repeatedly to create this effect.
Figure 21
10. EDITING A LOOP:
Please Note: Only the end point of the loop may be edited. You may make your loop shorter or longer. Before
you can edit your seamless loop you obviously must first have created a seamless loop to edit. If you haven’t
created a SEAMLESS LOOP, follow the instructions in step 9 to create a loop. If a SEAMLESS LOOP has
already been created, press the RELOOP BUTTON (19) to activate your SEAMLESS LOOP (Figure 21) if it is
not already activated. If the loop is located in one of the BANK BUTTONS (7) press the desired BANK BUTTON
to activate your loop. To edit your seamless loop’s ending point:
Make sure the loop that you want to edit is playing.
Now press and hold the RELOOP BUTTON (19) until
the start time of your loop is displayed.
- FOR A SHORTER LOOP: Turn the
JOG WHEEL
(1)
counter clockwise to make the loop shorter.
Press the OUT BUTTON to set the ending point
of your loop.
- FOR LONGER LOOP:
Turn the JOG WHEEL
(1)
clockwise. Press the OUT BUTTON to set the
ending point of your loop.
Notice: the time changes according to the setting
of the time display, i.e. REMAIN, TOTAL REMAIN,
or ELAPSED.
Figure 22