Nilfisk-ALTO CONTROL60 Stereo Equalizer User Manual


 
MIDI Controllers Values
d\u 0 1 2 3 4 5 6 7 8 9
0
15.0dB 14.5dB 14.0dB 13.5dB 13.0dB 12.5dB 12.0dB 11.5dB 11.0dB 10.5dB
10
10.0dB 09.5dB 09.0dB 08.5dB 08.0dB 07.5dB 07.0dB 06.5dB 06.0dB 05.5dB
20
05.0dB 04.5dB 04.0dB 03.5dB 03.0dB 02.5dB 2.0dB 1.5dB 1.0dB 00.5dB
30 00.0dB
00.5dB 01.0dB 01.5dB 02.0dB 02.5dB 03.0dB 03.5dB 04.0dB 04.5dB
40
05.0dB 05.5dB 06.0dB 06.5dB 07.0dB 07.5dB 08.0dB 08.5dB 09.0dB 09.5dB
50
10.0dB 10.5dB 11.0dB 11.5dB 12.0dB 12.5dB 13.0dB 13.5dB 14.0dB 14.5dB
60
15.0dB
Amplitude 15dB / 15dB step 0.5dB
(Value = d u)
Frequency 20Hz- 20KHz step 1/12 oct
(value = d u)
d\u0123456789
0 20 21,2 22,5 23,7 25 26,6 28,3 29,9 31,5 33,6
10
35,8 37,9 40 42,5 45 47,5 50 53,5 57 59,5
20 63 67 71,5 76 80 85 90 95 100 106,5
30 113 119 125 134 143 151,5 160 170 180 190
40 200 212,5 225 237,5 250 266,5 283 299 315 336,5
50 358 379 400 425 450 475 500 532,5 565 597,5
60 630 672,5 715 757,5 800 850 900 950 1000 1062
70
1125 1187 1250 1337 1425 1512 1600 1700 1800 1900
80 2000 2125 2250 2375 2500 2662 2825 2987 3150 3362
90 3575 3787 4000 4250 4500 4750 5000 5325 5650 5975
100 6300 6725 7150 7575 8000 8500 9000 9500 10000 10625
110 11250 11875 12500 13375 14250 15125 16000 17000 18000 19000
120 20000
13
Notes:
If the system is in whatever control change command is ignored, except controller # 86.bypass
Select the channel to edit by means of the controller 0 (bank).
If the type of EQ is Graphic or Parametric , assign to controller 84 (Mode) the value to edit themono (1x60)
first 30 filters and the value 1 to edit the following 30 filters.
At EQ type change, the system loads a default preset belonging to the same EQ type.
Warnings:
1. Before starting a MIDI session please set on the Control60 the same MIDI channel used by the external controller.
2. During a MIDI control session the unit's graphic display is NOT updated.
3. After MIDI use of Control60 it's advisable to run a manual STORE to save preset changes done by means
of the external controller. After saving, reboot the Control60 to use it as a stand-along unit.