Filter
Top Products
MULTI-TASKER
12
12
If card 1, 2, and 3 are grouped as group 5 of
unit 1, send the [SELB1G5U1] [–] [–] [–]
command to decrease the volume for card 1, 2,
and 3 simultaneously.
9. [VBLyCnUi]
This command sets absolute bass level for
single card. Command Format: [VBLyCnUi]
y = Absolute bass level (y = 1 to 15)
n = Card ID number (n = slot # from 1 to 19)
i = Unit ID number (i = 0 to 9)
Example:
If the status of audio card 2 of unit zero is as
follows:
VOLIN1:2
VOLIN2:12
VOLIN3:18
VOLOUT:8
BASS:8
TREBLE:14
LOUDNESS:ON
After sending a command [VBL2CnUi] on
request [C2] we will the new status of card 2:
VOLIN1:2
VOLIN2:12
VOLIN3:18
VOLOUT:8
BASS:2
TREBLE:14
LOUDNESS:ON
[VBLyGkUi]
This command sets absolute bass level for a
group of cards. Command Format: [VBLyGkUi]
y = Absolute bass level (y = 1 to 15)
k = group number (k = # from 1-9)
i = Unit ID number (i = 0 to 9)
Example:
If card 1, 2, and 3 are grouped as group 5 of
unit 1, send the [VBLFG5U1] command to set
maximum volume of bass for card 1, 2, and 3
simultaneously.
10. [SELTCnUi]
This command sets path to adjust the treble
level for single card. Command Format:
[SELTCnUi] [–] [–] [–] [–] or [+] [+] [+] [+]
n = Card ID number (n = slot # from 1 to 19)
i = Unit ID number (i = 0 to 9)
+ = increases volume. (maximum of 15 levels
for treble).
– = decreases volume. (maximum of 15 levels
for treble).
Example:
If the status of audio card 5 of unit zero is as
follows:
VOLIN1:2
VOLIN2:12
VOLIN3:18
VOLOUT:8
BASS:8
TREBLE:14
LOUDNESS:ON
Send commands [SELTC5] [-] [-] [-] [-]. After
executing that command, send [C5] to get the
new status of card 5: [On123C5]
VOLIN1:2
VOLIN2:12
VOLIN3:18
VOLOUT:8
BASS:8
TREBLE:10
LOUDNESS:ON
[SELTGkUi]
This command sets path to adjust the bass level
for a group of cards. Command Format:
[SELTGkUi] [–] [–] [–] [–] or [+] [+] [+] [+]
k = group number (k = # from 1-9)
i = Unit ID number (i = 0 to 9)
+ = increases volume. (maximum of 15 levels
for treble).
– = decreases volume. (maximum of 15 levels
for treble).
Example:
If card 1, 2, and 3 are grouped as group 5 of
unit 1, send the [SELTG5U1] [–] [–] [–]
command to decrease the treble volume for
card 1, 2, and 3 simultaneously.
11. [VTLyCnUi]
This command sets absolute treble level for
single card. Command Format: [VTLyCnUi]
y = Absolute treble level (y = 1 to 15)