Filter
Top Products
3
Sound Pressure Level (SPL): 105 dB
Total Continuous Power: 75 Watts RMS
• Front Speakers: 12.5 Watts/channel @ 4 ohms
@ 10% THD @ 180 – 15000 Hz
2 Channels Loaded
• Subwoofer: 50 Watts @ 4 ohms
@ 10% THD @ 40 – 180 Hz
Single Channel Loaded
System Response: 32 Hz – 18 kHz (-10 dB)
Signal to Noise Ratio
@ 1 kHz input: > 75 dB
Drivers (per satellite): Six 1" full-range micro drivers
Subwoofer
Driver: One 6.5" long-throw woofer
System Specifications
Connecting a Second Device
This auxiliary or secondary input is located on the wired controller. Connect any
audio source that has a stereo 3.5 mm plug (i.e. headphone style plug), including
portable CD or MP3 players.
Caution: Make sure the audio source features a line-out jack. This will ensure that
the output is not amplified. Check the owner’s manual for your audio device for
more information.
Note: You may need a cable that has RCA plugs on one end and a 3.5 mm stereo
male plug on the other or 3.5 mm stereo plugs on both ends. These types of
plugs may be purchased at most electronics stores.
POWERING ON
1. After all other connections are made plug the AC power cord from the back of
the subwoofer into an AC outlet.
2. Turn on the audio source.
3. Install the supplied battery in the remote’s battery compartment.
4. Turn on the PT6021 speaker system by pressing the power button on the
wired controller or wireless speaker system remote. A blue EQ LED on the wired
controller will illuminate next to the power button indicating power is on.
Push the “Power” button again to turn off the system.
Note: To avoid hearing popping sounds when you turn on your PT6021 speaker
system, always turn on your audio source first.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type.
Using the Wireless Speaker System Remote and
Wired Controller
Master Volume Control
The knob on the wired controller is the master volume control for the speaker
system. Turn the knob clockwise to increase the volume and counter-clockwise to
decrease the volume.
When using the wireless speaker system remote press and hold the “+” button to
increase the volume or press and hold the “–” button to decrease the volume.
Blue EQ LED’s will light up on the wired controller to indicate volume level. The
number of LED’s lit will increase as the volume increases to a maximum of 5 for
full volume.
Bass
Press the bass button on the wired controller or wireless speaker system remote.
A blue EQ LED will illuminate next to the bass button. When using the wired
controller, turn the master volume knob clockwise to increase the bass and
counter-clockwise to decrease the bass.
When using the wireless speaker system remote, press and hold the “+” button
to increase the bass or press and hold the “–” button to decrease the bass.
An LED will light up and move on the wired controller to indicate changing bass
levels. The LED will reside in the far right position for maximum bass and in the
far left position for minimum bass.
After a few seconds, bass will default back to main volume. To return to bass
control, press the bass button again.
Treble
Press the treble button on the wired controller or wireless speaker system
remote. A blue EQ LED will illuminate next to the treble button. When using the
wired controller, turn the master volume knob clockwise to increase the treble
and counter-clockwise to decrease the treble.
When using the wireless speaker system remote, press and hold “+” button to
increase the treble or press and hold the “–” button to decrease the treble.
An LED will light up and move on the wired controller to indicate changing
treble levels. The LED will reside in the far right position for maximum treble and
in the far left position for minimum treble.
After a few seconds, treble will default back to main volume. To return to treble
control, press the treble button again.
Stand-By
To mute the PT6021 press the stand-by button on the wired controller or wireless
speaker system remote. The blue LED located next to the power button will
turn off. To un-mute, press the stand-by button again.
It is important to note that while in stand-by mode the system continues to
receive power. To completely shut down the PT6021, press the standby button
on the wired controller or wireless speaker system remote and then unplug the
unit from the wall.
Headphones
To use headphones with the system, plug them into the labeled jack on the
side of the wired controller. When headphones are connected, both satellite
speakers and the subwoofer are muted.