Filter
Top Products
28-EN
Adjusting Sound Setting in Manual Mode
You can change these sound settings to create your own preference
when the MultEQ mode is set to MULTEQ OFF (Manual Mode).
1
Press IMPRINT to activate the Sound menu
selection mode.
2
Turn the Rotary encoder to select the desired item,
and then press
/ENT.
SUBWOOFER SUBW SYSTEM
*
1
SUBW PHASE
*
1
SUBW CHANNEL
*
1
FACTORY’S EQ TW SETUP
*
2
FILTER TYPE MEDIAXPANDER MX LEV MODE
*
3
EQ MODE T.CORR PARA SOUND ADJUST
*
4
SUBWOOFER
(e.g. Select SUBWOOFER)
*
1
These functions are inoperable when SUBWOOFER is set to OFF.
*
2
This function can be operable only when PXA-H100 (sold
separately) is connected and 2.2ch (3WAY) mode is set. For details,
refer to the Owner’s Manual of PXA-H100.
*
3
This function is inoperable when MEDIAXPANDER is set to OFF.
*
4
In step 2, three sound adjustment items (PARAMETER EQ/
GRAPHIC EQ, T.CORRECTION, CROSSOVER) can be selected in
SOUND ADJUST mode, turn the Rotary encoder to select the
desired item, and then press
/ENT to continue to step 3.
3
Turn the Rotary encoder to change the setting,
and then press
/ENT.
(e.g. Select SUBW ON or SUBW OFF)
4
Press and hold /ESC for at least 2 seconds to
return to normal mode.
• MEDIAXPANDER FACTORY’S EQ, PARAMETER EQ/GRAPHIC
EQ, EQ MODE and MX LEV MODE Adjustment are inoperable
when DEFEAT is set to ON.
• Pressing /ESC returns to the previous Sound menu mode.
• If no operation is performed for 60 seconds, Sound menu mode is
canceled.
When the subwoofer is on, you can adjust the subwoofer output level
(refer to
page 13).
SUBW OFF SUBW ON (Initial setting)
When the subwoofer is on, you can select either System1 or System2
for the desired subwoofer effect.
SUBW SYS 1 (Initial setting) SUBW SYS 2
NORMAL (Initial setting) REVERSE
The subwoofer output phase is toggled SUBWOOFER NORMAL (0°)
or SUBWOOFER REVERSE (180°). To adjust the level, turn the
Rotary encoder.
You can set the subwoofer output to stereo or monaural. Make sure to
set the correct output for your subwoofer type.
STEREO (Initial setting) MONO
10 typical equalizer settings are preset at the factory for a variety of
musical source material.
FLAT POPS ROCK NEWS JAZZ&BLUES
ELEC DANCE HIP HOP&RAP EASY LISTEN
COUNTRY CLASSICAL USER 1 USER 2
USER 3 USER 4 USER 5 USER 6
• By selecting USER 1 to 6, you can recall the stored preset number in
“Adjusting the Graphic Equalizer Curve” (page 30) or “Adjusting
the Parametric Equalizer Curve” (page 29).
“Setting the response characteristic of tweeter to FLAT in 2.2ch
(3WAY) mode could damage the speaker. Make sure the Crossover
cut-off is appropriate for the tweeter being used (see “Adjusting the
Crossover Settings” on page 30).”
MAKER’S (Initial setting) USER’S
Use steps 1 to 4 to select one of the Sound menu
modes to modify. See the applicable section below for
details about the selected item.
Turning Subwoofer ON/OFF
Setting the Subwoofer System
SUBW SYS 1 : Subwoofer level changes according to the main
volume setting.
SUBW SYS 2 : Subwoofer level change is different from the
main volume setting. For example, even at low
volume settings, the subwoofer is still audible.
Setting the Subwoofer Phase
Setting the Subwoofer Channel
(SUBW CHANNEL)
STEREO: Subwoofer stereo (L/R) output
MONO: Subwoofer monaural output
Equalizer Presets (FACTORY’S EQ)
Setting the Response Slope for the High
Range Speaker (TW SETUP)
MAKER’S: As protection from possible speaker damage, FLAT
cannot be set for the response slope of the high
range speaker in 2.2ch (3WAY) mode.
USER’S: The FLAT setting is possible in 2.2ch (3WAY) mode.