Technicolor - Thomson CS500 Stereo System User Manual


 
7
EN
6
EN
Sound Features
Volume Control
Turn VOLUME on the main unit or press VOL or
on the remote control to adjust volume level.
X-Bass
Press X-BASS to turn on/off boosting the bass
frequency.
Muting Audio
Press MUTE on the remote to cut the sound.
(Remote Only)
Using Preset Equalizer Curves
Press EQ to toggle among FLAT, ROCK, POP, JAZZ,
CLASS and CUSTOM. The display shows the selection
briefly.
Creating a Custom Curve
1. Press EQ to select CUSTOM mode.
2. While CUSTOM is displayed, press SKIP
BACKWARD or SKIP FORWARD on the
main unit or SKIP BACKWARD or SKIP
FORWARD on the remote control to cycle
among displayed bass- and treble - range levels.
3. While BAS or TRE is displayed, adjust VOLUME
to set the associated gain between -10 - +10.
CD Player
Loading Discs
1. Press SOURCE repeatedly on the main unit or CD
on the remote control to select CD mode.
2. Press DISC OPEN/CLOSE on the front panel of
the main unit or OPEN/CLOSE on the remote
control to open disc compartment.
3. Insert up to 5 discs with label face up.
4. Press DISC OPEN/CLOSE on the front panel of
the main unit or OPEN/CLOSE on the remote
control again to close disc compartment. The disc
that is loaded and ready to play is the icon that is
flashing on the display.
Play and Pause Discs
• Press PLAY/PAUSE in stop mode to begin
playback.
•Press PLAY/PAUSE during playback to to
pause disc.Press again to resume.
Play and load simultaneously by:
1. Press DISC OPEN/CLOSE on the front panel of
the main unit or OPEN/CLOSE on the remote
control to open the tray while a CD is playing.
2. Load/change discs for available trays.
3. Press DISC OPEN/CLOSE on the front panel
of the main unit or OPEN/CLOSE on the remote
control to close the tray.
This unit is compatible with
CD-RW/ CD-R discs for play-
back.
Notes on CD-R/RW Disc:
Do not affix any type of labels to either side
(recordable or labeled side) of a CD-R/RW disc
as this may result in the unit malfunctioning.
To avoid damages to the CD-R/RW disc, do not
open the disc compartment door while the
disc is being read.
Do not load an unrecorded CD-R/RW disc into
the unit. This may take a longer time to read
the disc.
Playback capability for CD-RW discs may
vary due to variations in the quality of
the CD-RW disc and the recorder used to
create the disc.
CD-R / RW
Settings
Showing the Demonstration
Press DEMO to turn on/off demonstration mode.
The demonstration scrolls through all display
operations.
Display Clock / Timer
Setting the Clock
1. Press and hold CLOCK to enter clock setting
mode. The hour flashes on the display.
2. Press SKIP BACKWARD or SKIP FORWARD
on the main unit or PRESET or PRESET
on the remote control to set the hour .
Press CLOCK to shift to minute digits.
3. Press SKIP BACKWARD or SKIP FORWARD
on the main unit or PRESET or PRESET
on the remote control to set the minute .
4. Press PROG/SET to save settings.
Press STOP to quit settings.
Note:
• When system is ON, you can press CLOCK to
display the current time for about 2 seconds.
Setting the Timer
1. Press and hold TIMER until the ON and clock
hour flashes on the display ( ON - timer on time ).
2. For setting time, press SKIP BACKWARD or
SKIP FORWARD on the main unit or PRESET
or PRESET on the remote control to set
the hour and then press TIMER to shift to minute
digits.
3. Press SKIP BACKWARD or SKIP FORWARD
on the main unit or PRESET or PRESET
on the remote control to set the minute.
4. Press TIMER to change to OF (timer off time)
with clock time flashing. Repeat steps 2 & 3 for
timer off time setting.
5. Press TIMER to select source. Press SKIP
BACKWARD or SKIP FORWARD on the
main unit or PRESET or PRESET on the
remote control to select between CD / TUNER /
TAPE /REC TU.
If REC TU is selected, press SKIP BACKWARD
or SKIP FORWARD on the main unit or
PRESET or PRESET on the remote
control to select the preset station.
6. Press TIMER to set volume. Adjust VOLUME
control to select desired volume level.
7. Press PROG/SET to save settings.
Press STOP to quit setting.
The timer is automatically activated once timer
setting is saved.
Activating the Timer
Press and release TIMER to turn on/off the alarm.
The timer is active when the clock icon indicator
is displayed.
Sleep Mode
You can select the time interval in minutes before
the unit turn off automatically. Press SLEEP to select
among OFF, 120, 90, 60, 45, 30, 15 and 5 minutes.
Note: Be sure to remove all discs from the disc
compartment before moving or transporting the
unit!