Filter
Top Products
10
LISTENING TO A PROGRAM SOURCE
OOppeerraattiioonnss
BBeeffoorree ooppeerraattiioonn
Select the desired input source.
3
Enter the standby mode.
The STANDBY indicator lights up. This means
that the receiver is not disconnected from the AC
mains and a small amount of current is retained to
support the memorized contents and operation
readiness.
To switch the power off, push the POWER switch
again.
Then the power is cut off and the STANDBY
indicator goes off.
Each time the POWER button on the remote
control is pressed, the receiver is turned on to enter
the operating mode or off to enter the standby
mode.
In the standby mode, if the INPUT SELECTOR
button is pressed, the receiver is turned on
automatically and the desired input is selected.
Then sound can be heard from the speakers
connected to the speaker terminals.
When using headphones for private listening, press
the SPEAKER switch again to switch the speakers
off.
Each time the “AUDIO” button is pressed, the input
source changes as follows;
TUNER CD AUX
(frequency display)
Each time the “VIDEO” button is pressed, the input
source changes as follows;
VCR1 VCR2 DVD
When the TAPE MONITOR button is set to on so that
“TAPE M” indicator lights up, other inputs can not be
heard from the speakers.
To listen to a input source other than TAPE
MONITOR, be sure to set the TAPE MONITOR
button to off.
TAPE MONITOR function
You can connect either a tape deck or a graphic equalizer to
the receiver’s TAPE MONITOR jacks.
To listen to the component connected to these jacks, set the
TAPE MONITOR button to on.
If you connect a 3-head tape deck, you can listen to the sound
being recorded during recording, not the source sound.
For further details, refer to the operating instructions of the
component connected.
In the standby mode, turn the power on.
1
Switch the speakers on.
2
When selecting the 6 CH DIRECT as desired,
“6-DIRECT” is
displayed and the 6
separate analog
signals from 6 CH
decoder connected to
this unit pass through
the tone (bass, treble)
and volume circuits only and directly transfer to the
speakers. (In case that the TAPE MONITOR button
is set to on, the TAPE MONITOR button is
automatically set to off.)
To cancel the 6 CH Direct function, press the 6 CH
DIRECT button or select the desired input source.
These 6 separate analog signals can be heard only,
not recorded.
EENNGGLLIISSHH
POWER P.SCAN
DECK
DISPLAY
SLEEP
T.TONE
D.TIME
ADJUST
DVD/TV
DSP MODE
12345
67890
A
B
CD
TUNERVCR 1
AUXTAPE MON.
VCR 2 STEREO
INPUT
SELECTOR
6CH DIRECT
DECK SEL.
SYS
CD
INTROREPEAT
A B
<
<
DISC
PRESET
USER FILET.MONDISPLAY
EQUALIZER
CH LEVEL MASTER
MUTE
CH SEL.
AUDIO
VIDEO
INPUT SELECTOR
or
TAPE MONITOR
DVD/TV
CD
TUNER VCR 1
AUX TAPE MON.
VCR 2
POWER P.SCAN
DECK
DISPLAY
SLEEP
T.TONE
D.TIME
ADJUST
DVD/TV
DSP MODE
12345
67890
A
B
CD
TUNERVCR 1
AUXTAPE MON.
VCR 2 STEREO
INPUT
SELECTOR
6CH DIRECT
DECK SEL.
SYS
CD
INTROREPEAT
A B
<
<
DISC
PRESET
USER FILET.MONDISPLAY
EQUALIZER
CH LEVEL MASTER
MUTE
CH SEL.
AUDIO
VIDEO
INPUT SELECTOR
or
or
POWER
DVD/TV
CD
TUNER VCR 1
AUX TAPE MON.
VCR 2
INPUT
SELECTOR
6CH DIRECT
POWER
ON
/
OFF
POWER P.SCAN
DECK
DISPLAY
SLEEP
T.TONE
D.TIME
ADJUST
DVD/TV
DSP MODE
12345
67890
A
B
CD
TUNERVCR 1
AUXTAPE MON.
VCR 2 STEREO
INPUT
SELECTOR
6CH DIRECT
DECK SEL.
SYS
CD
INTROREPEAT
A B
<
<
DISC
PRESET
USER FILET.MON DISPLAY
EQUALIZER
CH LEVEL MASTER
MUTE
CH SEL.
6 CH
DIRECT
or
6CH DIRECT
SPEAKER
ON/ OFF