Filter
Top Products
51
ENGLISH
• Loud test tones are output from each speaker and then if auto speaker setup procedure has been completed, the
results of each adjustment will be displayed.
• Each time the ENTER button is pressed, the auto speaker setup procedure will start or stop.
• If there may be a problem with speaker or microphone connection, error message will be displayed. In this case,
turn off the power, check the connection as illustrated in error message and then retry the auto speaker setup
procedure.
• For your reference, “ASR” / “ASL” stands for Surround A
Right/Left and “BSR” / “BSL” for Surround B Right/Left.
• Auto Speaker Setup lets you avoid troublesome listening-based speaker setup and achieve good surround sound.
You should connect the supplied microphone to the SETUP MIC jack so that this receiver can analyze the
information from a series of test tones emitted from speakers and can adjust the size, distance and sound level of
each speaker automatically.
• If you want to personalize your speaker setup and channel level setup by making the settings manually, perform
the “When selecting the SPEAKER CONFIGURATION” procedure on page 45, “When selecting the
SPEAKER DISTANCE” procedure on page 47, “Adjusting each channel level with test tone” and “Adjusting
the current channel levels” procedures on page 33.
Preparations
1. Connect the supplied microphone to the SETUP
MIC jack on the rear panel.(For details, refer to
“CONNECTING MICROPHONE” on page 13.)
Note:
• After you have completed the auto speaker setup
procedure, be sure to disconnect the microphone.
2. Place the microphone on a flat level surface at your
normal listening position.
• If possible, use a tripod, etc. to attach the microphone at
the same height as your ears would be when you are
seated in your listening position.
• Ensure there are no obstacles between the speakers and
the microphone.
3. For the speakers to be set to “Small”, select the desired
crossover frequency performing the “CROSSOVER
FREQ.” procedure.(For details, refer to “When selecting
the CROSSOVER FREQUENCY” on page 50.)
Press the CURSOR UP( )/DOWN( ) buttons to select the AUTO SPEAKER SETUP, then press
the ENTER button.
1
Press the ENTER button to start the auto speaker setup procedure.
2
When selecting the AUTO SPEAKER SETUP
STANDBY
POWER ON
MAIN
P
A
G
E
FAV
MUTE
CH.
SET
VOL
RETURN
DISP
MI
OSD/MENU
1
STEREO
CH/
ADJUST
2
3
4
5
6
7
8
9
0
ENT
M2
M3
DSP
DECODE
DSP
RNC-510
RETURN:Back ENTER:Select
START
AUTO SPEAKER SETUP
FL : 0
dB
,L,10ft
FC: 0
dB
,L,10ft
FR: 0
dB
,L,10ft
ASR: 0
dB
,L,10ft
BSR: 0
dB
,L,10ft
BR: 0
dB
,L,10ft
BL: 0
dB
,L,10ft
BSL : 0
dB
,L,10ft
Channel level
Speaker size
Speaker distance
STANDBY
POWER ON
MAIN
P
A
G
E
FAV
MUTE
CH.
SET
VOL
RETURN
DISP
MI
OSD/MENU
1
STEREO
CH/
ADJUST
2
3
4
5
6
7
8
9
0
ENT
M2
M3
DSP
DECODE
DSP
RNC-510
RETURN:Back ENTER:Select
MEMORY
AUTO SPEAKER SETUP
FR : 0
dB
,L,10ft
ASR: 1
dB
,S,10f t
BSR:
dB
,N, f t
BR: 1
dB
,S,09ft
BL:+2
dB
,S,09ft
BSL :
dB
,N, f t
ASL: 1
dB
,S,09ft
SW:+8
dB
Result report