Filter
Top Products
6
Quick Start
Position the transmitter about 6-12” (15-30 cm) from the front of the CR88 with
the transmitter’s IR window facing the IR transmitter on the front panel of the CR88
receiver.
Press and hold the CR88 SELECT button to set the transmitter to the same channel as
the receiver via infrared transmission. The CR88 display will flash while the receiver is
sending the operating channel.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
3. Plug in receiver 4. Turn on receiver
5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set7. Install batteries 8. Turn on belt pack transmitter
When the transmission is complete, the CR88
will receive RF signal from the transmitter.
The READY indicator will light on the front
panel of the CR88 receiver.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
3. Plug in receiver 4. Turn on receiver
5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set7. Install batteries 8. Turn on belt pack transmitter
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
3. Plug in receiver 4. Turn on receiver
5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set7. Install batteries 8. Turn on belt pack transmitter
Turn on your connected amplifier or mixer,
but keep the volume all the way down. Set the
Volume knob on the CR88 fully clockwise (to
its “10” setting). This is unity gain.
Speak or sing into the microphone. Slowly
raise the volume of your amplifier or mixer
until the desired level is reached.
If you find the system has noticeable
dropouts, reduced overall working range,
or unexpected noise bursts, change the
operating channel of the system using the
steps above.
Note: The AH8 will only accept infrared transmission from the receiver for
the first 10 seconds after the AH8 is powered on. If you need to change
the operating channel, the AH8 must be first powered off, then powered on
again to receive the new channel.