Filter
Top Products
28
the delay setting. To return to the MAIN menu,
press the ENTER button. Press the MENU key
on the remote to cancel the display and re-
turn to normal operation.
SUBWOOFER SETUP Menu
SUB SETUP
CROSSOVER: 100HZ
DOLBY: +01dB
DTS: -02dB
STEREO: +05dB
MUSIC: +03dB
ENT KEY=MAIN MENU UP KEY=up
+/– KEY=change DWN KEY=down
The SUBWOOFER SETUP menu allows selec-
tion of the subwoofer crossover frequency and
independent adjustment of subwoofer level for
each surround mode. These settings are memo-
rized and engaged automatically each time
a music or theater surround mode is selected.
When going to the SUBWOOFER SETUP menu
from the MAIN menu, the current surround
mode is automatically highlighted. Use the +/–
buttons to adjust the subwoofer level (–10dB
to +10dB) for the current surround mode.
NOTE
: Only the current surround mode can
be adjusted on this menu. You will need to
change surround modes using the front-panel
or remote buttons to adjust a different mode.
The CROSSOVER setting activates a low-pass
filter for the subwoofer and a corresponding
high-pass filter for all SMALL speakers in the
system at the selected frequency. To adjust the
crossover frequency, highlight the CROSSOVER
line using the UP/DOWN buttons. Then, use
the +/– buttons to chose one of the following
options: OFF, 40Hz, 60Hz, 80 Hz, 100 Hz,
or 120 Hz.
NOTE
: The OFF setting sends a full-range sig-
nal to your subwoofer so that you can use its
built-in low-pass filter. With the OFF setting,
a 100 Hz high-pass filter is activated for all
SMALL speakers in the system.
To return to the MAIN menu, press the EN-
TER button. Press the MENU key on the remote
to cancel the display and return to normal
operation.
TEST TONE Menu
TEST TONE
LEFT: +01dB
CENTER: -01dB
RIGHT: +02dB
R SURROUND: +05dB
CENTER BACK: +05dB
L SURROUND: +04dB
SUBWOOFER: +09dB
ENT KEY=MAIN MENU UP KEY=up
+/– KEY=change DWN KEY=down
This menu uses test tones to set equal volume
levels for all speakers (left front, center, right
front, right surround, left surround, center back,
and subwoofer) to ensure proper surround
sound reproduction. Setting the output levels
using the test procedure provides the most ac-
curate adjustment so that digital surround sound
material will be reproduced as it was intended.
NOTE
: If you have configured your system to
use two center back speakers, there will be
an additional line in the menu, giving you
the ability to independently adjust the CEN-
TER BACK 1 and CENTER BACK 2 speak-
ers.
To access this menu and perform the test tone
calibration, you must be in one of the surround
modes. To do this, press any of the MODE
buttons except 2CH. Then, enter the ON-
SCREEN DISPLAY menu system and select TEST
TONE from the MAIN menu to reach this
screen.
When you enter the TEST TONE menu, you
will hear a test tone coming from the highlighted
speaker. Highlight different speakers by moving
the cursor to the desired line using the UP/
DOWN buttons. The test tone will shift accord-
ingly to the selected speaker.
While seated in the normal listening location,
switch the test tone to the various speakers.
Using the loudest speaker as a fixed reference,
listen to hear if any other speakers are notice-
ably louder or quieter. If so, adjust that speaker’s
volume levels up or down (in 1dB increments)
to match using the +/– buttons. Continue switch-
ing among the speakers and adjusting until
all speakers are the same volume.
NOTE
: This calibration will be more accurate
using a sound pressure level (SPL) meter in-
stead of relying on your ear. Set the meter to
its SLOW response time with C-weighting and
hold it away from your body. Adjust the lev-
els until the meter provides the same reading
for each of the speakers in your system.
To return to the MAIN menu, press the EN-
TER button. Press the MENU key on the remote
to cancel the menu display and return to nor-
mal operation.
OTHER OPTIONS Menu
OTHER OPTIONS
RECORD: CD
DYNAMIC: Max
MULTI INPUT: Off
CINEMA EQ: Off
POWER: Direct
OSD: On
LANGUAGE: English
ENT KEY=MAIN MENU UP KEY=up
+/– KEY=change DWN KEY=down
This menu, accessed from the MAIN menu,
provides access to a several miscellaneous
settings as follows:
RECORD: Select a signal for the record out-
puts by choosing one of the input sources.
DYNAMIC: steps through the three dynamic
range settings available in digital modes:
• MAX (no compression/full dynamic range)
• MID (moderate compression)
• MIN (full compression/minimum dynamic
range).
MULTI INPUT: determines whether the MULTI
channel input is turned ON or OFF.
CINEMA EQ: determines a special equaliza-
tion setting is turned ON or OFF. This equal-
ization may be desirable for playback of movie
source material to compensate for the acous-
tic differences between a commercial cinema
and a home theater environment. The CIN-
EMA EQ setting can also be changed using
the FILTER button on the remote.
RSX-1065 Surround Sound Receiver