Filter
Top Products
27
DS-2 Specifications
System
Overall Frequency Response
25Hz—25kHz
-3dB Frequency Response Limits
35Hz—25kHz
Subwoofer to Front Main/Center Crossover Design
Active 4th order (24dB/octave) low-pass and high-pass,
80Hz acoustic crossover.
Maximum Sound Pressure Level
108 dB in an IEC Standard 80 cubic meter
(2825 cubic foot, e.g. 15'W x 22'L x 8
1
⁄2'H) room
RT800i
Driver Complement:
2-6
1
⁄2" magnetically shielded Dynamic Balance midrange drivers
1-1" magnetically shielded Dynamic Balance Trilaminate Dome tweeter
Crossover Design:
2nd order Low Pass Filter @2.5kHz
2nd order High Pass Filter @2.5kHz
Dimensions:
40
1
⁄4"H x 8"W x 10
1
⁄2"D
Base Dimensions:
9
1
⁄8"W x 10
3
⁄4"D
f/x500i
Driver Complement:
1-6
1
⁄2" Dynamic Balance driver
2-1" Dynamic Balance Trilaminate Dome tweeters
Crossover Design:
2nd order Low Pass Filter @1.5kHz
2nd order High Pass Filter @1.5kHz
Dimensions:
15
1
⁄4"H x 9
7
⁄8"W x 9
1
⁄2"D
includes depth of wall mounting brackets
CS400i
Driver Complement:
2-6
1
⁄2" magnetically shielded Dynamic Balance drivers
1-1" magnetically shielded Dynamic Balance Trilaminate Dome tweeter
Crossover design:
2nd order Low Pass Filter cascaded @1.5kHz and 800Hz
2nd order High Pass Filter @1.5kHz
Dimensions:
8
5
⁄
8"H x 18
3
⁄
4"W x 12
1
⁄
8"D
Subwoofer
Driver Complement:
1-10" magnetically shielded driver with 1
1
⁄
2" voice coil, polypropylene
cone and butyl rubber surround
Crossover design:
Fixed, active 4th order (24dB/octave) low-pass with amplitude shaping
Cabinet Dimensions:
18
3
⁄4"H x 15
1
⁄2"W x 19
1
⁄2"D
Six Channel Power Amplifier
System Continuous Power Output
Greater than 500 Watts into 4 Ohms,
all channels driven*
Dynamic Power Output:
700 watts into 4 Ohms, all channels driven*
Bandwidth
20Hz-22kHz
Distortion
0.05%
Power Requirement
AC 120V, 50/60Hz
Maximum Power Consumption
800 Watts
Preamp/Processor
FM Tuner Section
Usable Sensitivity IHF 1.3 eV/13.5dBf
Signal to noise ratio Mono/Stereo 76/68dB
Distortion Mono/Stereo 0.2/0.5%
Stereo Separation 1 kHz 40dB
Alternate Channel Selectivity ± 400kHz 65dB
Image Rejection 98 MHz 50dB
AM Tuner Section
Usable Sensitivity: Loop 500µV
Signal to noise ratio 50dB
Selectivity ± 20kHz 70dB
Image Rejection 98 MHz 50dB
General
Power Requirement AC 120V 60Hz
Power Consumption (AC-3 RF) 26W
Dimensions (Max) 17
1
⁄
4"W x 4
1
⁄
2"H x 14"D
*Power ratings alone cannot predict actual sound output. Loudspeaker
efficiency is by far the most important factor in determining how loud your
system will play. For this reason we also specify the calculated maximum
sound output of the DS-2 system in a 2825 cu ft. room (for example,
one measuring approximately 15'W x 22'L x 8
1
⁄2'H). The maximum SPL
(volume) of the DS-2 in such a room would be 105 dB, as loud as
a rock band at 150 feet; certainly loud enough to get you evicted from
a New York City apartment. There are worse fates.
Polk Customer Service (800) 377-7655