Filter
Top Products
30 31
en
Regulatory Notices
FCC Registration Information
Changes or modifications to this product not expressly approved by our company, or operation of this
product in any way other than as detailed by the owner’s manual, could void your authority to operate
this product.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the
bottom of this equipment is a label that contains, among other information, a product identifier in the format
US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. An applicable
Universal Service Order Codes (USOC) certification for the jacks used in this equipment is provided (i.e.,
RJ11C) in the packaging with each piece of approved terminal equipment. A plug and jack used to connect
this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA.
A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to
a compatible modular jack that is also compliant. See installation instructions for details. The REN is used to
determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone
line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of
RENs should not exceed five (5.0).
To be certain of the number of devices that may be connected to a line, as determined by the total RENs,
contact the telephone provider. For products approved after July 23, 2001, the REN for this product is part
of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN
without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on
the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance
that temporary discontinuance of service may be required. But if advance notice isn’t practical, the
telephone company will notify the customer as soon as possible. Also, you will be advised of your right to
file a complaint with the FCC if you believe it is necessary. The telephone company may make changes
in its facilities, equipment, operations or procedures that could affect the operation of the equipment.
If this happens the telephone company will provide advance notice in order for you to make necessary
modifications to maintain uninterrupted service.
Please follow instructions for repairing if any (e.g. battery replacement section); otherwise do not alternate or
repair any parts of device except specified.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public
service commission or corporation commission for information.
NOTICE: If your home has specially wired alarm equipment connected to the telephone line, be sure that
installing the system does not disable your alarm equipment. If you have questions about what will disable
alarm equipment, consult your telephone company or a qualified installer.
Should you experience trouble with this equipment, please contact our service center for repair or warranty
information. If the equipment is causing harm to the telephone network, the telephone company may request
that you disconnect the equipment until the problem is resolved.
NOTICE: According to telephone company reports, AC electrical surges, typically resulting from lightning
strikes, are very destructive to telephone equipment connected to AC power sources. To minimize damage
from these types of surges, a surge arrestor is recommended.
To insure the safety of users, the FCC has established criteria for the amount of radio frequency energy
various products may produce depending on their intended usage. This product has been tested and found
to comply with the FCC’s exposure criteria. For body worn operation, the FCC RF exposure guidelines were
also met when used with accessory (belt clip) supplied or this product. Use of other accessories may not
ensure compliance with FCC RF exposure guidelines and should be avoided.
The antenna(s) used for the base-unit must be installed to provide a separation distance of at least 20 cm
from all persons and must not be collocated or operated in conjunction with any other antenna or transmitter.
Radio interference may occasionally cause buzzing and humming in your cordless dial pad, or clicking
noises in the base. This interference is caused by external sources such as TV, refrigerator, vacuum cleaner,
fluorescent lighting, or electrical storm. Your unit is NOT DEFECTIVE. If these noises continue and are too
distracting, please check around your home to see what appliances may be causing the problem. In addition,
we recommend that the base not be plugged into a circuit that also powers a major appliance because of
the potential for interference. Be certain that the antenna on the unit is fully extended when needed. In the
unlikely event that you consistently hear other voices or distracting transmissions on your phone, you may
be receiving radio signals from another cordless telephone or other source of interference. If you cannot
eliminate this type of interference, you need to change to a different channel. Finally, it should be noted that
some cordless telephones operate at frequencies that may cause interference to nearby TVs and VCRs. To
minimize or prevent such interference, the base of the cordless telephone should not be placed near or on
top of a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or
VCR will often reduce or eliminate the interference.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation. Privacy of communications may not be ensured
when using this phone.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
I.C. Notice
Terminal Equipment
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that
registration was performed based on a Declaration of Conformity indicating that Industry Canada technical
specifications were met. It does not imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment
itself. The REN assigned to each terminal equipment provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The termination on an interface may consist of
any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers
of all the devices does not exceed five.
Radio Equipment
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications
were met.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device.
“Privacy of communications may not be ensured when using this telephone.”