Filter
Top Products
32
En
07
Using the Tuner
Finding a Station
The following steps show you how to tune in to FM and
AM radio broadcasts using the automatic (search) and
manual (step) tuning functions. If you already know the
exact frequency of the station you want to listen to, see
Tuning Directly to a Station on this page. Once you are
tuned to a station you can memorize the frequency for
recall later—see Memorizing Stations on page 33 for
more on how to do this.
1 Press the MULTI CONTROL TUN button on
the remote control.
On the receiver, use the MULTI JOG to select the
tuner mode.
2 Use the BAND button to change the band
(FM or AM), if necessary.
Each press switches the band between FM and AM
On the receiver, pressing the BAND button switches
between bands.
3 Tune to a station.
Automatic tuning
To search for stations in the currently selected band,
press and hold either the TUNE + or TUNE – button
for about a second. The receiver will start searching
for the next station, stopping when it has found one.
Repeat this step to search for other stations.
Manual tuning
To change the frequency one step at a time, press the
TUNE + or TUNE – (%fi) buttons.
High speed tuning
Press and hold the TUNE + or TUNE – button for
high speed tuning, releasing the button once the
desired frequency is reached.
Tuning Directly to a Station
Sometimes, you'll already know the frequency of the
station you want to listen to. In this case, you can simply
enter the frequency directly using the number buttons
on the remote control (this function is not available
using the front panel controls of the receiver).
1 Press the MULTI CONTROL TUN button on
the remote control.
On the receiver, use the MULTI JOG to select the
tuner mode.
2 Press the BAND button to select either FM
or AM.
Each press switches the band between FM and AM.
On the receiver, pressing the BAND button switches
between bands.
3 Press D.ACCESS (DIRECT ACCESS).
4 Use the number buttons to enter the
frequency of the radio station.
Example: To tune to 106.00 (FM), press 1 – 0 – 6 –
0 – 0
SP
A
STEREO
TUNED
MEMO:
• If you make a mistake while inputting the frequency,
press the
D.ACCESS button twice to cancel the
frequency and start again.
2
1
MPX
VOLUME
MASTER VOLUME
CHANNEL
ENTER
ENTER
DISC
DTV INFO
MPX/RETURN
DTV ON/OFF DTV MENU
D.ACCESS GUIDE
ST
TUNE
TUNE
ST
CLASS
ATT
BAND
/DTS DSP
TEST TONE
CH SELECT CH LEVEL FUNCTION
SIGNAL SELECT
1¡
4
¢
7
8
3
¶
EFFECT
DVD VCR CD-RTV
RCV
TUN
TVC
CD
MIDNIGHT
LOUDNESS
MUTING
SETUP
FL DIMMER
MULTI CONTROL
5.1 / 7.1
RECEIVER
SOURCE
1
2
3
4
5
6
7
8
9
0
10
2
3
VOLUME
MASTER VOLUME
CHANNEL
ENTER
ENTER
DISC
DTV INFO
MPX/RETURN
DTV ON/OFF DTV MENU
D.ACCESS GUIDE
ST
TUNE
TUNE
ST
CLASS
ATT
BAND
/DTS DSP
TEST TONE
CH SELECT CH LEVEL FUNCTION
SIGNAL SELECT
1¡
4
¢
7
8
3
¶
EFFECT
DVD VCR CD-RTV
RCV
TUN
TVC
CD
MIDNIGHT
LOUDNESS
MUTING
SETUP
FL DIMMER
MULTI CONTROL
5.1 / 7.1
RECEIVER
SOURCE
1
2
3
4
56
7
8
9
0
10
2
2
1
3
4
MPX mode
If the TUNED or STEREO indicators don't light when
tuning to an FM station because the signal is weak, press
the MPX button to switch the receiver into mono
reception mode. This should improve the sound quality
and allow you to enjoy the broadcast.