Filter
Top Products
The System Setup menu
09
32
En
• Depending on the source and other receiver
settings, you may not always hear sound from the
subwoofer.
LFE attenuator setting
Dolby Digital and DTS audio sources include ultra-low
bass tones. Set the LFE attenuator as needed to prevent
the ultra-low bass from distorting the sound.
•
LFEATT 0
– The LFE channel is played with no
attenuation
•
LFEATT10
– LFE channel is attenuated by 10dB
•
LFE OFF
– LFE channel is not played
Front speaker distance setting
Specifies the distance from your listening position to the
front speakers:
•
Fch 0.1 m.
–
Fch 9.0 m.
– Distance can be set in
increments of 0.1 m. The default is 2.0 m.
Center speaker distance setting
Specifies the distance from your listening position to the
center speaker:
•
Cch 0.1 m.
–
Cch 9.0 m.
– Distance can be set in
increments of 0.1 m. The default is 2.0 m.
Surround speaker distance setting
Specifies the distance from your listening position to the
surround speakers:
•
Sch 0.1 m.
–
Sch 9.0 m.
– Distance can be set in
increments of 0.1 m. The default is 2.0 m.
Dynamic Range Control
Specifies the amount of dynamic range adjustment to
Dolby Digital soundtracks:
•
DRC OFF
– No dynamic range adjustment (use when
listening at higher volume)
•
DRC MAX
– Dynamic range is reduced (loud sounds
are reduced in volume while quieter sounds are
increased)
•
DRC MID
– Mid setting
• This setting works only with Dolby Digital
soundtracks. For other sources you can create a
similar effect using the Midnight mode (see
Using
the Sound Modes
on page 24).
Dual mono setting
Specifies how dual mono encoded Dolby Digital
soundtracks should be played:
•
ch1
– Only channel 1 is played
•
ch2
– Only channel 2 is played
•
L. c1 R. c2
– Both channels are played through the
front speakers
• On the
ch1
and
ch2
settings the sound comes only
from the center speaker (or from the front speakers if
CENTER ––
was selected for the center speaker
setting.
• This setting works only with dual mono encoded
Dolby Digital soundtracks. See the disc packaging
for channel information.
Input attenuator setting
When playing analog sources, if the sound is distorting
(or when you see the
OVER
indicator light in the display),
switch on the input attenuator. Each input has its own
attenuator setting; set it for the currently selected input.
•
IN. ATT OFF
– Input attenuator is off
•
IN. ATT ON
– Input attenuator is on
Coaxial input setting
Specifies which receiver function the coaxial input
(
DVD(STB) COAX
jack) relates to:
•
COAX DVD
– Assigns the input to the receiver’s
DVD
function
•
COAX STB
– Assigns the input to the receiver’s
STB
function (the optical input is automatically set to
DVD
)
• See also
Connecting your equipment
on page 8.
Optical input setting
Specifies which receiver function the optical input
(
STB(DVD) OPT1
jack) relates to:
•
OPT1 STB
– Assigns the input to the receiver’s
STB
function
•
OPT1 DVD
– Assigns the input to the receiver’s
DVD
function (the coaxial input is automatically set to
STB
)
• See also
Connecting your equipment
on page 8.
• You cannot assign the other optical input (
DVR/TV
OPT2
jack).
vsx-c301.book 32 ページ ２００３年２月６日 木曜日 午後５時４分