Filter
Top Products
Using the tuner
07
28
En
3 Press ENTER to search for the program type.
The tuner searches through the FM stations stored in the
station memories.
If the tuner finds a matching program type, the tuner
plays 5 seconds of the station. To listen to that station,
press the
ENTER
button. (The tuner stops searching.)
If you don’t press the
ENTER
button during the above
mentioned 5 seconds, the tuner resumes the search.
When the tuner finds a program type you searched for,
the frequency display will blink for about 5 seconds and
then the display will show
FINISH
briefly.
If
NO PTY
is displayed it means the tuner couldn’t find
that program type at the time of the search.
• This function searches RDS stations preset in the 30-
station memory. If there are no station presets, or if
the program type could not be found among the
station presets
NO PTY
is displayed.
Enhanced Other Network (EON)
EON (Enhanced Other Network information) allows you
to set the receiver to switch automatically to a news or
traffic information broadcast. Once set, the receiver will
scan for stations transmitting news or traffic
announcements even when it’s in a different input
function (
DVD
, for example). When the broadcast ends,
the tuner returns to the original frequency or input
function.
EON can only be used in areas where EON data is
transmitted, and it only works with FM broadcast
stations that transmit RDS program type (PTY)
information.
The
EON
indicator lights when EON is set. The dot
indicator to the left lights when the current broadcast
carries the EON data service.
1 Press the FM/AM button to put the receiver in
FM tuner mode.
2 Press EON to select the EON mode.
Press repeatedly to switch between:
•
TA
(Traffic Announcement) – Sets the tuner to pick
up traffic information when it is broadcast.
•
NEWS
– Sets the tuner to pick up news when it is
broadcast.
•
OFF
– Switches off the EON feature.
When set to
TA
or
NEWS
, the
EON
indicator in the
display lights. When the receiver switches automatically
to an EON broadcast, the dot indicator blinks.
• The EON function does not work when listening to
AM reception, or when the AV Direct function is on
(see on page 9 and
AV Direct setting
on page 33).
• Simultaneous requests for Traffic Information (
TA
)
and News (
NEWS
) is not possible.
• When EON is turned on and a function other than
the tuner is selected, the function will switch to the
FM station automatically when Traffic Information or
News begins. When the program ends, the original
function will be restored.
• You cannot use the
T.EDIT
and
SEARCH
buttons
while the
EON
indicator in the display is lit.
• You can’t change the input function while receiving
an EON broadcast. If you want to change to a source
other than tuner, press
EON
and turn the EON mode
to
OFF
.
Program identification function
The receiver will automatically register an identifying
marker (called a PI code) for any station you input into
the memory classes which can receive RDS or EON data.
If you want to remove the currently memorized stations
from RDS and EON searches, you can do it by erasing
the PI codes.
1 Tune to the station for which you want to erase
the PI marker.
2 Press EON for two seconds or more.
ERASE PI
is displayed.
3 Press ENTER within 5 seconds.
AUDIO
MODE
DIALOG
MUTE
MASTER
VOLUME
DTV MENU
TOP MENU
T.EDIT
MENU
GUIDE
SEARCH
SUBTITLE
ROOM
SETUP
TUNE
TUNE
STST
SYSTEM
SETUP
BAND
EON RETURN
RF ATT
A
DISPLAY
CLASS MPX
D.ACC ES S
ENTER
BCDE
DISC
ENTER
VIRTUAL SB
vsx-c301.book 28 ページ ２００３年２月６日 木曜日 午後５時４分