Filter
Top Products
10
<DRC1129>
En
Method of inserting discs one by one by
operating the Changer control panel
The disc installation, removal and exchanging methods are basically
identical. To simply install a disc, place a disc on the tray. To simply
remove a disc, remove the disc from the tray. To exchange a disc,
remove the disc on the tray and place another disc on it.
1. Insert the key into the Key switch and turn it
clockwise to the UNLOCK position.
÷ The switch is usually in the LOCK position while the key is not
inserted.
2. Specify the address to insert the disc with the
numeric buttons of the control panel.
÷ The address is originally a hex code between 0001h and 0064h.
However, in this case, specify it with a decimal number between
1 and 100.
÷ For example, pressing key “1” means address #1 and CH 1
appears on the mode indicator..
3. Press the ENT (ENTER) button of the control
panel.
÷ The mail slot opens.
4. Place a disc on the disc tray, with the label side
facing up.
Only one disc can be loaded in the tray of the mail slot. Do not load
more than one disc to prevent malfunction.
When placing a disc on the mail slot tray, place the disc with the label
side up so that it comes below the black parts on the left and right of
the deep of the tray.
÷ To exchange discs
Remove the disc on the tray and place the replacement disc on the
tray.
÷ To install a disc
Place the disc on the tray.
÷ To remove a disc
Take out the disc on the tray.
HOW TO INSTALL OR EXCHANGING DISCS
Method of inserting discs one by one issu-
ing commands from the host computer
The disc installation, removal and exchanging methods are basically
identical. To simply install a disc, place a disc on the tray. To simply
remove a disc, remove the disc from the tray. To exchange a disc,
remove the disc on the tray and place another disc on it.
1. Issue the POSITION TO ELEMENT command from
the host computer.
÷ The mail slot opens.
2. Place a disc on the disc tray, with the label side
facing up.
Only one disc can be loaded in the tray of the mail slot. Do not load
more than one disc to prevent malfunction.
When placing a disc on the mail slot tray, place the disc with the label
side up so that it comes below the black parts on the left and right of
the deep of the tray.
÷ To exchange discs
Remove the disc on the tray and place the replacement disc on the
tray.
÷ To install a disc
Place the disc on the tray.
÷ To remove a disc
Take out the disc on the tray.
3. Press the MAIL SLOT OPEN/CLOSE button.
÷ The MAIL SLOT closes.
4. Issue the MOVE MEDIUM command from the
host computer.
÷ The disc in the MAIL SLOT is stroed in the magazine.
It is possible to install 100 discs by repeating the above steps, but this
requires to operate both the host computer and Changer. Meanwhile,
the following method allows to install discs by operating only the
control panel of the Changer.
)
OPEN/CLOSE
TT
TTT
DOOR OPEN
0
1
2
3
45
6
7
8
9
LOOK
UNLOOK
POWER
MAIL SLOT
DRIVE 4
DRIVE 3
DRIVE 2
DRIVE 1
ESC
ENT
LOCK
UNLOCK
)
OPEN/CLOSE
TT
TTT
DOOR OPEN
0
1
2
3
45
6
7
8
9
LOOK
UNLOOK
POWER
100 DISCS CD -- ROM AUTCHANGER
MAIL SLOT
DRIVE 4
DRIVE 3
DRIVE 2
DRIVE 1
ESC
ENT
0
1
2
3
45
6
7
8
9
ESC
ENT
)
OPEN/CLOSE
)
OPEN/CLOSE
TT
TTT
DOOR OPEN
0
1
2
3
45
6
7
8
9
LOOK
UNLOOK
POWER
MAIL SLOT
DRIVE 4
DRIVE 3
DRIVE 2
DRIVE 1
ESC
ENT