Filter
Top Products
10
RQT9584
Getting StartedPlaying DiscsOther OperationsReference
Preparation
≥Make sure that there is an audio connection between this unit and the
TV or other device. (B 7)
≥Turn on the TV or/and other device.
Press [EXT-IN]4 to choose the source that is used to
connect this unit to the TV or other device.
≥To change the surround sound effects and sound mode, refer to
“Enjoying sound effects from all speakers” (B right).
≥If your Panasonic TV is VIERA Link compatible, refer to “Linked
operations with the TV” (B 14) for other related functions.
Select to suit the type of audio from the DIGITAL AUDIO IN OPTICAL and
HDMI AV OUT terminal on the main unit.
≥Underlined items are the factory presets.
§ Only when “D-IN” is selected.
Be sure to select the device’s (STB, etc.) input channel on the TV when
making the setting.
The device must be connected to the Panasonic TV via an HDMI cable
and to this unit with an optical digital audio cable.
≥If the device’s (STB, etc.) input channel on the TV is changed or if you
want to change the device allocated for the linked operations, select
the “STB” mode to “OFF” in step 3 above and then select “SET”
again.
≥This function will not operate if “DIGITAL IN” is selected in “TV Audio”
(B 17).
≥The following sound effects may not be available or may have no effect
with some sources.
≥You may experience a reduction in sound quality when these sound
effects are used with some sources. If this occurs, turn the sound effects
off.
When changing the surround sound effect, Whisper-mode Surround or the
sound modes, the setting is displayed on the TV screen if “DVD/CD” is the
selected source during video playback.
For “Front layout (Alternative)”
§
mode
STANDARD:
Stereo source is output as 2.1-channel audio.
When playing surround sources, you can enjoy 5.1-channel
surround-like effect even with all the speakers at the front.
STEREO:
You can play any source in stereo. Surround sound effect is
unavailable.
A.SRD (Advanced Surround):
You can enjoy surround effect with any audio source.
When the signal is DTS or Dolby Digital, “/DTS” or “/DOLBY DIGITAL” will
also be displayed respectively.
§ Selected mode in “Speaker layout” (B 8, Easy setup).
Listening to the TV or other device’s
audio from this unit’s speakers
Making settings for digital audio input
Available settings
Mode Setting
DUAL: (Only works with Dolby Dual Mono)
– MAIN+SAP
(stereo audio)
–MAIN
–SAP
“SAP” = Secondary Audio Program
≥Set PCM FIX mode to “OFF” to listen to the “MAIN” or
“SAP” audio.
DRC:
(Dynamic
Range
Compression)
–ON
Adjust for clarity even when the volume is low by
compressing the range of the lowest sound level and
the highest sound level. Convenient for late night
viewing. (Only works with Dolby Digital)
–OFF
The full dynamic range of the signal is reproduced.
PCM FIX: – ON
Select when receiving only PCM signals.
–OFF
Select when receiving Dolby Digital and PCM signals.
≥When receiving true 5.1-channel surround sound,
select “OFF”.
STB
§
:
(CABLE/SAT
AUDIO)
–SET
Select when setting the main unit to switch to
“D-IN” when the input channel of an HDMI connected
device (STB, etc.) is selected on the TV (B 14,
Setting the audio link with the STB).
–OFF
Select to cancel this setting.
1
Press [EXT-IN]4 several times to select “D-IN” or
“ARC”.
2
Press [PLAY MODE]9 and then [3, 4]8 to select the
mode.
3
While the selected mode is displayed, press [2, 1]8 to
select the desired setting.
Enjoying sound effects from all
speakers
Enjoying surround sound effects
Press [SURROUND];.
Each time you press the button:
For “Surround layout (Recommended)”
§
mode
STANDARD:
Sound is output as it was recorded/encoded. Speaker output varies
depending on the source.
MULTI-CH:
You can enjoy sound from the front speakers, as well as the surround
speakers and center speaker even when playing stereo sources.
MANUAL: (B below)
While “MANUAL” is displayed, press [2, 1]8 to select
other surround modes.
Each time you press [2, 1]8:
DOLBY PLII MOVIE
Suitable for movies, or videos recorded in Dolby Surround.
DOLBY PLII MUSIC
Adds 5.1-channel effects to stereo sources.
S.SRD (Super Surround)
You can enjoy sound from all speakers with stereo sources.
STEREO
Sound will only be output to the front speakers and the subwoofer from
any source.
Recommended modes to enjoy TV audio or stereo
sources from all speakers:
“MULTI-CH”, “DOLBY PL
II
MOVIE”, “DOLBY PL
II
MUSIC” or “S.SRD”
Selecting sound mode
1
Press [SOUND]: to select a sound mode.
Each time you press the button:
EQ: Equalizer
SUBW LVL: Subwoofer Level
C.FOCUS: Center Focus (Only when “Surround layout
(Recommended)” mode is selected in “Speaker
layout” (B 8, Easy setup).)
2
While the selected mode is displayed, press [2, 1]8 to
make the settings.
Refer to the following for setting details of each sound effect.
SC-XH170 PPC_eng.book 10 ページ ２０１１年１１月２５日 金曜日 午前１０時４３分