Filter
Top Products
Operations
25
VQT3Q59
Advanced operations
∫ Changing the dual audio
Change the dual audio from main to secondary.
1 Confirm the digital audio output setting on the
connected TV or player, etc. is set to “Bitstream”.
2 Press and hold [HDMI 1/2] for more than 2 sec.
3 While the indicator of the current setting is flashing,
press [HDMI 1/2] to change the setting.
≥ The setting works only when the dual audio is available
in the audio source.
≥ The setting is maintained until it is changed again.
≥ The same setting is used for [TV] and [HDMI 1/2] audio
sources.
∫ Remote control code
When other Panasonic devices respond to this system’s
remote control, change the remote control code on the
active subwoofer and the remote control.
Preparation
≥ Turn off all other Panasonic products.
≥ Turn on this system.
Change the remote control code to code 2:
1 Aim the remote control at this system’s remote control
sensor.
2 Press and hold [MUTE] and [HDMI 1/2] on the remote
control for more than 4 sec.
≥ All the indicators will blink for 10 sec when the code of
this system is changed.
≥ The setting is maintained until it is changed again.
≥ If this system does not operate after changing the code,
repeat steps 1 and 2.
≥ To change the remote control code to code 1, repeat the
steps above, but replace [HDMI 1/2] with [TV].
∫ To turn off the 3D surround effect and
clear-mode dialog effect
Depending on your preference, it is possible to use only
the Dolby Virtual Speaker effect by turning off the 3D
surround effect and the clear-mode dialog effect.
1 Press and hold [TV] for more than 2 sec.
≥ The indicator for the current setting blinks for 10 sec.
2 While the indicator is blinking press [TV] to change the
setting.
≥ The setting changes each time [TV] is pressed.
≥ The setting will be reset to on when this system is turned off.
∫ To turn off VIERA Link “HDAVI Control”
When “HDAVI Control” compatible equipment does not
work well with this system, for example, it is possible to
turn off this function as follows:
≥ When VIERA Link is turned off the ARC function is not
available. Be sure to connect the optical digital audio
cable. (> 19)
1 Press and hold [MUTE] on the remote control and
[s VOL] on the active subwoofer for more than 2 sec.
2 After the setting has changed, turn off all the
connected devices and then turn them on again.
∫ To reduce the clear-mode dialog effect
When the dialog does not sound natural while the volume
is set low, for example, it is possible to reduce the dialog
enhancing effect as follows:
Press and hold [TV] on the remote control and [s VOL] on
the active subwoofer for more than 2 sec.
∫ To turn off the volume limitation
If a state of the lowered volume disturbs you every time
this system turns on, for example, it is possible to turn off
this function as follows:
Press and hold [MUTE] on the remote control and [VOL
r
] on
the active subwoofer for more than 2 sec.
The settings of VIERA Link “HDAVI Control”, the clear-mode
dialog effect and the volume limitation remain intact even if you
switch this system to standby mode. To turn these 3 functions
back on, this system must be set back to the factory preset.
(> 26)
≥ All the indicators will blink once when the setting is changed.
The following settings are unnecessary under
general usage conditions of the system.
A : Main
B : Secondary (SAP: Secondary Audio
Program)
A, B : Main and secondary
Only Dolby Virtual Speaker is on.
3D surround effect and clear-mode
dialog effect are also on.
SC-HTB15PP_VQT3Q59_eng.book Page 25 Wednesday, June 8, 2011 3:33 PM