Filter
Top Products
11
RQTX1260
ENGLISH
Sound adjustment
The following sound effects can be added to the audio output.
≥ You may experience a reduction in sound quality when these effects are used
with some sources. If this occurs, turn the sound effects off.
Radio operations
1 Press [EXT-IN, RADIO] repeatedly to select
“FM” or “AM”.
2 Press [6] or [5] to select the frequency of
the required station.
≥ “ST” is displayed when a stereo FM broadcast is being
received.
≥ To tune automatically, press and hold [6] or [5] until
the frequency starts changing rapidly.
jTo cancel auto tuning, press [6] or [5] once again.
jAuto tuning may not function when there is excessive
interference.
∫ To improve FM sound quality
1 Press [RADIO MENU] to select “FM MODE” while receiving
FM broadcasts.
2 Press [2, 1] to select “MONO”.
≥ Select “STEREO” in Step 2 to return to stereo broadcasts.
≥ “MONO” is canceled if the frequency is changed.
∫ To improve AM sound quality
1 Press [RADIO MENU] to select “B.PROOF” while receiving
AM broadcasts.
2 Press [2, 1] to select the beat proof setting (“BP 1” or
“BP 2”) and press [OK].
≥ This setting is reset to “BP 1” when changes are made (e.g. frequency is
changed).
You can preset up to 30 FM channels and 15 AM channels.
Preparation
Press [EXT-IN, RADIO] repeatedly to select “FM” or “AM”.
∫ Automatic presetting
1 Press [OK] to switch between the “LOWEST” and
“CURRENT” frequency.
2 Press [AUTO PRESET].
“PGM” starts to flash and the tuner starts to preset all the stations
it can receive into the channels in ascending order.
∫ Manual presetting
1 Press [6] or [5] to tune to the required station.
2 Press [PROGRAM].
3 While “PGM” is flashing, press the numeric buttons to select
a channel.
≥ The station occupying a channel is erased if another station is preset in that
channel.
≥ To preset more stations, repeat steps 1 - 3.
∫ Selecting a preset station
Press [:] or [9] to select the channel.
≥ Alternatively, press the numeric buttons to select the channel.
This unit is factory-set to FM 0.2 MHz and AM 10 kHz, but you
can change it to receive broadcasts allocated in FM 0.1 MHz or
AM 9 kHz steps.
1 Press [EXT-IN, RADIO] to select “FM”.
≥ Select “AM” to change the AM frequency steps
2 Press and hold [RADIO/EXT-IN] on the main unit.
After a few seconds the display changes to display current
minimum frequency.
3 Continue to hold down [RADIO/EXT-IN] on the main unit.
When the minimum frequency changes, release the button.
≥ To return to the original step, repeat steps 1 - 3.
≥ After the setting is changed, any previously preset frequency will be cleared.
Preset EQ Press [PRESET EQ] repeatedly to select
“HEAVY”, “SOFT”, “CLEAR”, “VOCAL” or
“FLAT”.
Bass or Treble 1 Press [SOUND] repeatedly to select
“BASS” or “TREBLE”.
2 Press [2, 1] to adjust the level (-4 to
+4).
Surround
Sound
1 Press [SOUND] repeatedly to select
“SURROUND”.
2 Press [2, 1] to select
“ON SURROUND”.
≥ To cancel surround sound, select
“OFF SURROUND” in step 2.
≥ If interference in FM stereo reception
increases, cancel the surround sound
effect.
D.Bass Press [D.BASS] during play to select
“ON D.BASS” or “OFF D.BASS”.
Manual tuning
Memory preset
FM/AM frequency step
SC-HC55_35-RQTX1260.book 11 ページ ２０１１年４月４日 月曜日 午後４時５０分