Filter
Top Products
RQTX1249
10
ENGLISH
ENGLISH
■
iPod or iPhone
You cannot switch on the iPod or iPhone.
• Examine that the battery of the iPod or iPhone is not depleted.
• Switch off the iPod or iPhone and the system before you connect the
iPod or iPhone. Connect the iPod or iPhone and try again.
No sound
• Switch off the iPod or iPhone and remove from the system. Connect
the iPod or iPhone to the system and switch it on and play it again.
■
Main unit displays
“NO PLAY”
• Examine the content. You can only play supported format.
“F76” or “F61”
• There is a power supply problem.
“ERROR”
• An incorrect operation was done. Read the instructions and try again.
“NOT MP3/ERROR”
• An unsupported MP3 format. The system will skip that track and play
the next one.
“VBR–”
• The system cannot show the remaining play time for variable bit rate
(VBR) tracks.
“NODEVICE”
• The iPod or iPhone is not connected. Examine the connection.
Memory reset (Initialization)
When the following situations occur, refer to the instructions below to
reset the memory:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
To reset the memory
1
Disconnect the AC power supply cord.
(Wait 3 minutes before you continue with step 2.)
2
While you press and hold [1, POWER] on the main unit,
connect the AC power supply cord again.
“– – – – – – – –” shows on the display panel.
3
Release [1, POWER].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
Specifications
■
Amplifier section
RMS output power stereo mode
Front Ch (both ch driven)
5 W per channel (6
), 1 kHz, 10% THD
Total RMS stereo mode power 10 W
FTC output power stereo mode
Front Ch (both ch driven)
4.5 W per channel (6
), 60 Hz to 20 kHz, 10% THD
Total FTC stereo mode power 9 W
■
FM/AM tuner, terminals section
Preset station FM 30 stations
AM 15 stations
Frequency modulation (FM)
Frequency range 87.9 MHz to 107.9 MHz (200 kHz step)
87.5 MHz to 108.0 MHz (100 kHz step)
Antenna terminals 75
(unbalanced)
Amplitude modulation (AM)
Frequency range 520 kHz to 1710 kHz (10 kHz step)
522 kHz to 1629 kHz (9 kHz step)
Headphone jack
Terminal Stereo, 3.5 mm (
1
/
8
″) jack
AUX (rear)
Terminal Stereo, 3.5 mm (
1
/
8
″) jack
■
Disc section
Disc played [8 cm (3″) or 12 cm (5″)]
CD, CD-R/RW (CD-DA, MP3
formatted disc)
MPEG-1 Layer 3, MPEG-2 Layer 3
Pick up
Wavelength 790 nm (CD)
Laser power CLASS I (CD)
Audio output (Disc)
Number of channels 2 ch (FL, FR)
FL = Front left channel
FR = Front right channel
■
Speaker section
Type 1 way, 1 speaker system (bass reflex)
Speaker unit(s)
Full range 8 cm (3
1
/
8
″) cone type
Impedance 6
Frequency range 60 Hz to 25 kHz (–16 dB)
90 Hz to 22 kHz (–10 dB)
■
General
Power supply AC 120, 60 Hz
Power consumption 14 W
Dimensions (W x H x D) 400 mm x 221 mm x 110 mm
(15
3
/
4
″ x 8
3
/
4
″ x 4
1
/
2
″)
[D = 69 mm (2
3
/
4
″) minimum]
[D = 149 mm (5
3
/
4
″) tray open]
Mass (weight) 2.1 kg (4.6 lb.)
Operating temperature range 0°C to +40°C
(+32°F to +104°F)
Operating humidity range 35% to 80% RH (no condensation)
Power consumption in standby mode 0.1 W (approximate)
Note:
1) Specifications are subject to change without notice.
Mass and dimensions are approximate.
2) Total harmonic distortion is measured by the digital spectrum
analyzer.
Maintenance
To clean this system, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean this system.
• Before using chemically treated cloth, read the instructions that came
with the cloth carefully.
SC-HC25_P_en_sp.indd 10SC-HC25_P_en_sp.indd 10 2/10/2011 5:20:45 PM2/10/2011 5:20:45 PM