Filter
Top Products
52
En
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
You can set the crossover frequencies, distances, and
levels of the front speakers A and front speakers B
independently. The other speakers (i.e., subwoofer, center,
surround, surround back and front high) use the same
crossover frequencies, distances, and levels for Speakers
A and Speakers B. Specify “Full Band” for speakers that
can output low frequency bass sounds adequately, for
example, speakers with a good sized woofer. For smaller
speakers, specify a crossover frequency. Sounds below the
crossover frequency will be output by the subwoofer
instead of the speaker. Refer to your speaker’s manuals to
determine the optimum crossover frequencies. If you set
up your speakers using Audyssey MultEQ XT32 Room
Correction and Speaker Setup, please make sure manually
that any THX speakers are set to “80Hz(THX)” crossover.
■Subwoofer
`1ch:
Audio signal is outputted from SW1 jack only.
`2ch
:
Audio signal is outputted from SW1 and SW2
jacks.
`No
■Front
(Setting Speakers A and Speakers B)
`Full Band
`40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
,
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Note
•If the “Subwoofer” setting is set to “No”, the “Front” (Speakers
B) setting is fixed to “Full Band”.
• If any of “Center”, “Surround”, or “Front High” is set to “Full
Band”, the “Front” (Speakers B) setting is fixed to “Full
Band”.
■Center
*1
, Surround
*1
, Surround Back
*2*3*4*5
`Full Band
`40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
,
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
`None
■Front Wide
*2*6*7*8
, Front High
*1*2*7
`Full Band
`40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
`
None
Note
*1
“Full Band” can be selected only when “Full Band” is
selected in the “Front”(Speakers A) setting.
*2
If the “Surround” setting is set to “None”, this setting cannot
be selected.
*3
If the “Surround” setting is set to anything other than “Full
Band”, “Full Band” cannot be selected here.
*4
When the “Powered Zone 3” setting is set to “Yes”, this
setting cannot be used.
*5
When “Front High + Front Wide” is set to “Yes”, this
setting cannot be selected.
*6
“Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*7
If “Bi-Amp” is selected, or the “Powered Zone 2” setting is
set to “Yes”, this setting cannot be selected.
*8
If anything other than “No” is selected in “Speakers
Type(Front B)”, this setting cannot be selected.
■Surround Back Ch
`1ch:
Select if only one surround back speaker L is
connected.
`2ch
:
Select if two (left and right) surround back speakers
are connected.
Note
•If the “Surround Back” setting is set to “None”, this setting
cannot be selected.
■LPF of LFE
(Low-Pass Filter for the LFE Channel)
`80Hz, 90Hz, 100Hz, 110Hz, 120Hz
`Bypass:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff frequency
of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
Note
• If you’re using THX-certified speakers, select “80Hz”.
■Double Bass
`
On
`Off(THX)
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to the
subwoofer.
Note
• This function can be set only if the “Subwoofer” setting is set to
“1ch” or “2ch”, or the “Front” setting is set to “Full Band”.
• If you’re using THX-certified speakers, select “Off(THX)”.
This setting is set automatically by
Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup function (➔ page 33). For Speakers B,
you need to change the settings manually.
This setting is NOT set automatically by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function (➔ page 33).