Filter
Top Products
28
Connecting the power
STANDBY/ON
PHONES
VIDEO 4
INPUT
DIGITAL
VIDEO 3
TAPE
VIDEO
4
SURROUND THX DSP
STEREO
STANDBY
DISPLAY
VIDEO 2
DVD
VIDEO
1
AUDIO
SELECTOR
LISTENING MODE
MASTER VOLUME
RETURN
ENTER
AUDIO
ADJUST
SETUP
RT/PTY/TP
VCR 2VCR 1
S VIDEO
VIDEO
AUDIO
LR
OFF
ON
POWER
TUNER CD
PHONO
DIRECT/
PURE AUDIO
PURE AUDIO
REC OUT ZONE 2
OFF
LEVEL
MEMORY
CLEAR
FM MODE
PRESET
TUNI
NG
STANDBY/ON
PHONES
VIDEO 4
INPUT
DIGITAL
VIDEO 3
TAPE
VIDEO
4
SURROUND THX DSP
STEREO
STANDBY
DISPLAY
VIDEO 2
DVD
VIDEO
1
AUDIO
SELECTOR
LISTENING MODE
MASTER VOLUME
RETURN
ENTER
AUDIO
ADJUST
SETUP
DIMMER
VCR 2VCR 1
S VIDEO
VIDEO
AUDIO
LR
TUNER CD
PHONO
DIRECT/
PURE AUDIO
PURE AUDIO
REC OUT ZONE 2
OFF
LEVEL
MEMORY
CLEAR
FM MODE
PRESET
TUNI
NG
ON
RCVR
MODE
STANDBY/ON
STANDBY
POWER
STANDBY/ON
(USA and Canadian models and Australian models)
STANDBY indicator
(All models other than USA and Canadian models and
Australian models)
To wall outlet
To wall outlet
STANDBY indicator
• Turning on the power may cause a momentary power surge,
which might interfere with other electrical equipment on the
same circuit, such as computers. If this happens, use a wall
outlet on a different circuit.
(All models other than USA and Canadian models and
Australian models)
• The TX-SR701/701E/601/601E is shipped with the main power
(POWER) switch in the on position ( ). When the power
cord is plugged in for the first time, the TX-SR701/701E/601/
601E will automatically enter the standby state and the
STANDBY indicator will light (same condition after step 2
below).
1. Plug the power cord into an AC wall outlet.
(USA and Canadian models and Australian models)
The STANDBY indicator will light up.
(All models other than USA and Canadian models and
Australian models)
Press the POWER switch to set the TX-SR701/701E/
601/601E to standby state.
The STANDBY indicator will light up.
2. Press the STANDBY/ON button to turn on the TX-
SR701/701E/601/601E.
The display will light up and the STANDBY indicator will turn off.
If you press the STANDBY/ON button again, the receiver
returns to standby state.
Turning on the power
ON
Turn off
Before you can use the remote controller, you must perform step 1
above and place the TX-SR701/701E/601/601E in the standby state.
1. Press the RCVR MODE button.
The RCVR MODE button lights.
2. Press the ON button to turn on the
TX-SR701/701E/601/601E (take it out
of the standby state).
To return the TX-SR701/701E/601/601E to
the standby state, press the STANDBY
button.
Turning on the power from the remote controller
Memory preservation (Other than USA and Canadian
models and Australian models)
The TX-SR701/701E/601/601E does not require memory
preservation batteries. A built-in memory backup system
preserves the contents of memory (e.g., speaker settings and
surround settings) during power failures and even when the
power is turned off with the POWER switch. The backup system
is charged when the POWER switch is turned on.
The length of time that the memory will be preserved will vary
depending on the ambient climate. On the average, memory
contents are protected over a period of a few weeks after the last
time the unit has been turned off. This period may be shorter
when the unit is exposed to a highly humid climate.
Memory preservation (USA and Canadian models and
Australian models)
The TX-SR701/701E/601/601E does not require memory
preservation batteries. A built-in memory backup system
preserves the contents of memory (e.g., speaker settings and
surround settings) during power failures and even when the unit
is unplugged. The unit must be plugged in order to charged the
back-up system.
The length of time that the memory will be preserved will vary
depending on the ambient climate. On the average, memory
contents are protected over a period of a few weeks after the last
time the unit has been unplugged. This period may be shorter
when the unit is exposed to a highly humid climate.
Diagram for TX-SR701/701E
Diagram for RC-533M