Filter
Top Products
62
En
■ The AV receiver’s remote controller doesn’t
control your iPod
■ The AV receiver unexpectedly selects your iPod
as the input source
■ Can’t record
■ There’s no sound
■ The Zone 2 speakers produce no sound
■ The sound changes when I connect my
headphones
■ The speaker distance cannot be set as required
■ How do I change the language of a multiplex
source
■ The functions don’t work
■ The functions System On/Auto Power On and
Direct Change don’t work for components
connected via
■ When performing “Audyssey 2EQ
®
Room
Correction and Speaker Setup”, the
measurement fails showing the message
“Ambient noise is too high.”.
■ The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these set-
tings.
1. While holding down the input selector button for the input
source that you want to set, press SETUP.
2. Use / to change the setting.
3. Press the input selector button for the input source that you
want to set when you’ve finished.
• Video Attenuation
This setting can be made for the BD/DVD, VCR/DVR,
CBL/SAT, GAME, or AUX input.
If you have a games console connected to the composite
video input, and the picture isn’t very clear, you can
attenuate the gain.
Video ATT:OFF: (default).
Video ATT:ON: Gain is reduced by 2 dB.
Make sure the correct input is selected on your TV or
the AV receiver.
—
Some versions of the iPod do not output video. —
Make sure your iPod is properly inserted in the
Dock. If your iPod is in a case, it may not connect
properly to the Dock. Always remove your iPod
from the case before inserting it into the Dock.
—
The iPod cannot be operated while it’s displaying the
Apple logo.
—
Make sure you’ve selected the right remote mode. —
When you use the AV receiver’s remote controller,
point it toward your AV receiver.
—
When connecting UP-A1 Dock to the radio tuner
UP-HT1 with AUTO selected by the tuner’s Mode
Selector switch, you can switch the input source
between UP-A1 Dock and the tuner, by pressing
PORT repeatedly on the front panel.
—
If you still can’t control your iPod, start playback by
pressing your iPod’s Play button. Remote operation
should then be possible.
—
Try resetting your iPod. —
Depending on your iPod, some buttons may not
work as expected.
—
Always pause iPod playback before selecting a dif-
ferent input source. If playback is not paused, the
Direct Change function may select your iPod as the
input source by mistake during the transition
between tracks.
—
Recording
On your recorder, make sure the correct input is
selected.
—
To prevent signal loops and damage to the AV
receiver, input signals are not fed through to outputs
with the same name (VCR/DVR IN to VCR/DVR
OUT).
—
Zone 2
Only components connected to analog inputs can be
played in Zone 2.
—
Powered Zone 2 cannot be used if “Speakers Type”
is set to “Bi-Amp”.
35
To use the Zone 2 speakers, you must set the “Front
High/Front Wide/Zone2” setting to “Zone2”.
49
Others
When a pair of headphones is connected, the listen-
ing mode is set to Stereo, unless it’s already set to
Stereo, Mono or Direct.
—
In some cases, corrected values suitable for home
theater use may be set automatically.
—
Use the “Multiplex” setting on the “Audio Adjust”
menu to select “Main” or “Sub”.
37
To use , you must make an connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected dig-
itally.
17
These functions don’t work when Zone 2 is turned
on.
17
This can be caused by any malfunction in your
speaker unit. Check if the unit produces normal
sounds.
—