Filter
Top Products
Advanced Operations
En-49
Tuner
■ AM/FM Freq Step (North American and Brazilian
models)
`10kHz/200kHz
:
`9kHz/50kHz:
Select the frequency step according to your area.
■ AM Freq Step (Asian models)
`10kHz:
`9kHz
:
Select the frequency step according to your area.
For AM/FM tuning to work properly, you must specify the
AM/FM frequency step used in your area.
Note
• When this setting is changed, all radio presets will be deleted.
Auto Standby
■ Auto Standby
`Off
`On
When “Auto Standby” is set to “On”, the AV receiver
will automatically enter standby mode if there is no
operation for 30 minutes with no audio and no video signal
input.
“Auto Standby” will appear on the AV receiver’s display
and OSD 30 seconds before the Auto Standby comes on.
Default setting: On (Asian models), Off (North
American and Brazilian models)
Note
•Set to “
On”, the Auto Standby function may activate itself during
playback with some sources.
Menu HDMI Setup
■ HDMI Ctrl (RIHD)
`Off
`On
Turn this setting on to allow -compatible
components connected via HDMI to be controlled by the
AV receiver (➔ page 65).
Note
• When the setting is set to “On” and the menu is closed, the names
of connected -compatible components and “RIHD On”
are displayed on the AV receiver.
“Search…” → “(name)” → “RIHD On”
When the AV receiver cannot receive the name of the component,
it is displayed as “Player
*
” or “Recorder
*
”, etc (“
*
” shows up
and indicates the number of components, when two or more are
received).
• When an -compatible component is connected to the
AV receiver via an HDMI cable, the name of the connected
component is displayed on the AV receiver display. For example,
while you are watching TV broadcasting, if you operate a Blu-ray
Disc/DVD player (being powered on) with the remote control of
the AV receiver, the name of the Blu-ray Disc/DVD player will
be displayed on the AV receiver.
• Set it to
“Off” when a connected piece of equipment is not
compatible or it is unclear whether the equipment is compatible
or not.
• If operation is not normal when set to
“On”, change the setting to
“Off”.
• Refer to the connected component’s instruction manual for
details.
• When the “HDMI Ctrl (RIHD)” setting is set to “On”, the power
consumption in standby mode slightly increases. (Depending on
the TV status, the AV receiver will enter standby mode as usual.)
• When the source equipment is connected with the
connection, it may malfunction if “HDMI Ctrl (RIHD)” is set to
“On”.
■ HDMI Through
`Off
`BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,
TV/CD:
Selects the input source for which the HDMI
Through function is enabled.
`Last:
The HDMI Through function is activated on the input
source selected at the time of setting the AV receiver
to standby mode.
When enabling the HDMI Through function, regardless of
whether the AV receiver is on or in standby, both audio
and video streams from an HDMI input will be output to
the TV or other components via HDMI connection. In
standby mode, the HDMI THRU and HDMI indicators
will light (HDMI will be dimly-lit).
This setting is fixed to “Auto” automatically when the
above “HDMI Ctrl (RIHD)” setting is set to “On”,
resulting in automatic input source selection.
Note
• Only the input source assigned to the HDMI IN via
“HDMI Input” is enabled (➔ page 41).
• The power consumption in standby mode will increase during the
HDMI Through function; however in the following cases, the
power consumption can be saved:
– The TV is in standby mode.
– You are watching a TV program.
• Refer to the connected component’s instruction manual for
details.
• Depending on the connected component, the correct input source
may not be selected with the setting fixed to “Auto”.
• This setting is set to “Off” automatically when the “HDMI Ctrl
(RIHD)” setting is set to “Off”.
HDMI Setup
123456