En-44
Controlling Other Components
iPod/iPhone Playback
via Onkyo Dock
UP-A1 Dock
With the UP-A1 Dock, you can easily play the music,
photo, or movie stored on your Apple iPod/iPhone through
the AV receiver and enjoy great sound.
You can use the AV receiver’s remote controller to operate
your iPod/iPhone.
■ System Function
Auto Power On
If you start iPod/iPhone playback while the AV receiver is
on Standby, the AV receiver will automatically turn on and
select your iPod/iPhone as the input source.
Direct Change
If you start iPod/iPhone playback while listening to another
input source, the AV receiver will automatically select
your iPod/iPhone as the input source.
Using the AV receiver’s Remote Controller
You can use the AV receiver’s remote controller to control
basic iPod/iPhone functions (
➔ page 45).
■ Using Your iPod/iPhone models Alarm Clock
You can use your iPod/iPhone models Alarm Clock
function to automatically turn on your iPod/iPhone and the
AV receiver at a specified time. The AV receiver’s input
source will automatically be set to the PORT selector.
Note
• To use this function, your iPod/iPhone must be in the UP-A1
Dock, and the UP-A1 Dock must be connected to the AV
receiver.
• This function works only in the Standard mode (➔ page 46).
• When you use this function, be sure to set the AV receiver’s
volume control to a suitable level.
• You cannot use this function for sound effects on your
iPod/iPhone.
•“UP-A1 ChargeMode” must be set to “On” to enable the Alarm
Clock (➔ page 40).
■ Charging Your iPod/iPhone models Battery
The UP-A1 Dock charges your iPod/iPhone models battery
while your iPod/iPhone is in the UP-A1 Dock connected to
the AV receiver. While your iPod/iPhone is seated in the
UP-A1 Dock, its battery will be charged when the AV
receiver is set to on or standby.
You can specify how the power is fed to your iPod/iPhone
when the AV receiver is in standby mode (
➔ page 40).
Note
• When UP-A1 Dock that seated iPod/iPhone is connected, the
power consumption in standby mode slightly increases.
■ Status Messages
If either of the following message is not displayed on the
AV receiver’s display, check the connection to your
iPod/iPhone.
• PORT Reading
The AV receiver is checking the connection with the
dock.
• PORT Not Support
The AV receiver do not support the connected dock.
•PORT UP-A1
UP-A1 Dock is connected.
Note
• The AV receiver displays the message “UP-A1” for several
seconds after recognizing the UP-A1.
Using the Onkyo Dock
The Dock is sold separately. Models sold are different
depending on the region.
For the latest information on the Onkyo Dock
components, see the Onkyo web site at:
http://www.onkyo.com
Before using the Onkyo Dock components, update
your iPod/iPhone with the latest software, available
from the Apple web site.
For supported iPod/iPhone models, see the instruction
manual of the Onkyo Dock.
The AV receiver may take several seconds to startup, so
you might not hear the first few seconds of the first song.
■ Operating Notes
• Functionality depends on your iPod/iPhone model and
generation.
• Before selecting a different input source, stop iPod/iPhone
playback to prevent the AV receiver from selecting the
iPod/iPhone input source by mistake.
• If any accessories are connected to your iPod/iPhone, the AV
receiver may not be able to select the input source properly.
• When connecting UP-A1 Dock to the radio tuner UP-DT1 with
AUTO selected by the tuner’s Mode Selector switch, you can
switch the input source between UP-A1 Dock and the tuner, by
pressing PORT repeatedly on the front panel.
• While your iPod/iPhone is in the UP-A1 Dock, its volume
control has no effect. If you adjust your iPod/iPhone models
volume control while it’s in the UP-A1 Dock, make sure it’s
not set too high before you reconnect your headphones.
• The Auto Power On function will not work if you set your
iPod/iPhone in the UP-A1 Dock while it is playing.
• Do not turn off the power with the iPod/iPhone still connected
to this unit via the UP-A1 Dock.
• Set your iPod/iPhone in the UP-A1 Dock after the AV receiver
turns on.
•“UP-A1 ChargeMode” must be set to “On” to enable the Auto
Power On and Direct Change functions (➔ page 40).