Filter
Top Products
The specifications above are correct at the time of printing of this manual. For improvement purposes, all specifications for this unit,
including design and appearance, are subject to change without prior notice.
SPECIFICATIONS
7
NOTICE
The information in this document is subject to change, as the Company may make changes to product in order to improve reliability,
design, or function, without prior written notice. No part of this manual may be reproduced or transmitted in any form or by any means
without the written permission of the company.
IN NO EVENT WILL THE COMPANY BE LIABLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER
ARISING DIRECTLY OR INDIRECTLY, SUCH AS LOSS OF PROFIT OR GOOD WILL, THAT MAY BE SUFFERED IN CONNECTION
WITH THE PURCHASE OF THIS PRODUCT OR FROM THE BREACH OF ANY REPRESENTATION OR WARRANTY.
LICENSE
The Company grants the customer a non-exclusive, non-transferable license to use the software, if any, accompanying this product for
internal use on a single computer system. The end user may make a single copy of the software solely for backup purposes; otherwise,
no copies may be made of the software or any part thereof. No other license of any kind is granted to any part of the product or any of
the intellectual property therein.
LEGAL INFORMATION
Input Impedance: ................................................600 Ω balanced,
50K Ω TRS unbalanced (1/4”)
Output Impedance: ........................... 50K Ω TRS balanced (1/4”)
Max Input Level: ......................-15dBV XLR 600Ω, +18dBV (1/4”)
Max Gain: .............................................................................+65dB
Max Output Level: ...............................................................+22dB
Frequency Response:................................... 20Hz-25KHz +/-3dB
Total Harmonic Distortion (THD) + Noise: .......................... 0.1%
Noise Floor: ..........................................................................-75dB
Equalizer Boost/Cut:.........................................................+/-15dB
Equalizer Settings:.......................................LOW SHELF: 150Hz
HIGH SHELF: 10KH
MID FREQUENCIES: 300Hz-5KHz, Q=1
Compressor Settings: ................THRESHOLD: -30dB to +20dB;
RATIO: 2:1 to 8:1
Indicators:........................... PHANTOM POWER, CLIP, POWER,
ANALOG VU METER
Input/Output Jacks: ...................XLR balanced, 1/4” unbalanced,
1/4” TRS unbal. Side Chain
Dimensions:......................... 19" x 1.75" x 6" (483 x 44 x 162mm)
Weight: ................................................................3.5 lbs.( 1.75 Kg)
and the RATIO (13) control low (fully counterclockwise). This is a
very low compression setting. To increase the amount of
compression, lower the THRESHOLD (12) control and increase
the RATIO (13) control until the desired amount is achieved.
USING THE SIDE CHAIN (19)
To use the SIDE CHAIN (19) to directly access the compressor
circuitry you'll need an insert cable like the one shown above. The
Tip-Ring-Sleeve stereo end plugs into the TMP-3 SIDE CHAIN
lack. The 1/4" SEND plug connects to the Input of a signal
processor such as an equalizer, the 1/4" RETURN plug connects
to the signal processor Output. The signal in the SIDE CHAIN is
not heard on the Output of the TMP-3, it only effects the action of
the compressor. The higher the level of signal in the SIDE CHAIN,
the more compression will occur.
EQUALIZER SETTINGS (7,8,9,10)
Begin with all controls set at 0 or center detente position. This is
the equivalent of a "bypass". Adjusting the LEVEL (15) controls
will increase or decrease the amount of the indicated frequency
range. The MID SWEEP (9) control adjusts the actual frequency
that the MID LEVEL (8) control will adjust.
USING THE PROCESSES TOGETHER
Increasing the Mic Preamp GAIN settings to the point where slight
distortion occurs will effect the overall frequency content of the
output signal. EQ adjustments may need to be made. Experiment
with different settings until you've achieved the desired sound.
Connects to tip SEND
Connects to ring RETURN