Filter
Top Products
8
ENGLISH
REMOTE CONTROLLER
RC8500SR
NAMES AND FUNCTIONS
z
Infrared Transmitter and Learning
Sensor
This transmitter emits infrared light. Press the
buttons while pointing the transmitter towards the
infrared receiver window of the SR7500 or other
AV equipment. Be sure to also point towards other
remote controls when using the learning function.
x
POWER ON and OFF buttons
(When AMP mode is selected)
These buttons are used to turn the SR7500 on or
off.
c
SOURCE ON/OFF button
This button is used to turn a specific source (such
as a DVD player) on or off independently from the
rest of the system.
v
M (Mode) button
This button is used to program Macros. Pressing
this button switches between Normal mode and
Macro mode.
The > button is used to move to the next page. Up
to 20 programs (4 pages) can be made. Holding
down the M button for three seconds or more
switches to the Setup mode, where the Setup
menu is shown on the LCD. The Setup menu has
four pages, and the > button is used to move to the
next page. Pressing the > button from page 4
returns you to page 1.
b
D1 to D5 (Direct) buttons
Five types of direct operations can be performed
for each of the 12 source buttons such as the DVD,
television, amplifier, and other AV equipment. The
pages can be switched, so 4 pages × 5 types = 20
operations can be performed for a single source.
The text display can also be changed.
n
> (Page) button
This button is used to switch pages for the Direct
button. The current page is shown on the LCD.
m
VOL (Volume) button
This button is used to adjust the volume for the
amplifier and television.
Note:
• Set the AMP mode to use this button with the
SR7500.
2 31
5 64
8
0
97
MEMO
CLEAR
DSS
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
VCRDVD
TV
SOURCE
OFF
ON/OFF
POWER
ON
D4
D5
D2
M
D1
D3
D5
OK
VOL
CH
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
LIP·SYNC
THX
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
SLEEP
12
LIGHT
Learning Remote Controller
RC8500SR
z
c
v
b
n
x
m
,
.
⁄1
⁄2⁄6
⁄7
⁄8
⁄9
¤0
¤1
⁄3
⁄4
⁄5
⁄0
!8
AUDIO IN/OUT (CD, TAPE, CD-R, TV,
DVD, VCR1, DSS/VCR2)
These are the analog audio inputs and outputs.
There are 7 audio inputs (4 of which are linked to
video inputs) and 4 audio outputs (2 of which are
linked to video outputs). The audio jacks are
nominally labeled for cassette tape decks,
compact disc players, DVD players and etc.... The
audio inputs and outputs require RCA-type
connectors.
!9
DIGITAL INPUT (Dig.1 - 6) / OUTPUT
(coaxial, optical)
These are the digital audio inputs and outputs.
There are 3 digital inputs with coaxial jacks, 3 with
optical jacks.
The inputs accept digital audio signals from a
compact disc, LD, DVD, or other digital source
component.
For digital output, there is 1 coaxial output and 1
optical output.
The digital outputs can be connected to MD
recorders, CD recorders, DAT decks, or other
similar components.
@0
DVI-D INPUT / OUTPUT (SR8500 only)
This unit has two DVI-D inputs and one DVI-D
output. The input function can be selected from the
SETUP MAIN MENU.
,
MUTE button
This button is used to mute the audio for the
SR7500 and television.
Note:
• Set the AMP mode to use this button with the
SR7500.
.
GUIDE button
This button is used to display the menus for the
DVD player, DSS (satellite broadcasting tuner), or
other AV equipment.
(when AMP mode is selected)
This button is used to select the LIP.SYNC mode.
⁄0
EXIT button
(when AMP mode is selected)
This button is used to cancel settings in the setup
menu.
⁄1
Numeric buttons
These buttons are used to switch between 0 to 9 of
the source components. If the source is set to the
amplifier, these buttons are used to perform
operations.
(when AMP mode is selected)
(1) TEST button
Used to enter the test tone menu.
(2) CH SEL. (channel select) button
Used to call up SETUP MAIN MENU and adjust
speaker levels or 7.1 ch input level.
(3) SURR (surround) button
Used to select the surround mode.
(4) 7.1CH button
Press this button to select the output of an external
multi channel decoder.
(5) ATT button
When the input signal is too high and the voice
distorts even by throttling the SR7500 VOLUME
control, turn on this function. “ATT” is indicated
when this function is activated.
The input level is reduced. Attenuator is invalid for
use with the output signal of “REC OUT”.
Note:
• This function is unavailable during the digital
input is selected.
(6) SPK-AB button
Speaker mode is switched in the following
sequence.
A → B → A+B → off