Filter
Top Products
8
ENGLISH
REAR PANEL
v RS232C
The RS232C port is to be used in conjunction with an external
controller to control the operation of the SR7300 by using an external
device.
The RS232C port may also be used in the future to update the
operating software of the SR7300 so that it will be able to support new
digital audio formats and the like as they are introduced.
b MONITOR OUT
This is a monitor output and each one includes both composite video
and S-video configurations. When connecting two video monitors or
televisions, be aware that the OSD interface can be used with both
MONITOR OUT.
n Preamp Outputs (L, R, SL, SR, SBL,
SBR, C)
Jacks for L(front left), R (front right), C (Center), SL (surround left), SR
(surround right), SBL (surround back left) and SBR (surround back
right).
Use these jacks for connection to some external power amplifiers.
m Power cable
Connect to AC power outlet.
SR7300 can be powered by 120 V AC only.
Caution:
• In order to avoid potential turn-off thumps, anything plugged in
here should be powered up BEFORE the SR7300 is turned on.
z VIDEO IN/OUT (TV, DVD, VCR1, DSS/
VCR2)
These are the video inputs and outputs. There are 4 video inputs and
2 video outputs and each one includes both composite video and S-
video configurations. Connect VCRs, DVD players, and other video
components to the video inputs.
S-video sources can be viewed through the S-video outputs, and
composite sources can only be viewed through the composite output.
The 2 video output channels can be used to be connected to video
tape recorders for making recordings.
x FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial cable, or a cable
network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the terminals marked
“AM” and “GND”. The supplied AM loop antenna will provide good
AM reception in most areas. Position the loop antenna until you hear
the best
c COMPONENT VIDEO INPUT/OUTPUT
If your DVD player or other device has component video connectors,
be sure to connect them to these component video connectors on the
SR7300. The SR7300 has two component video input connectors to
obtain the color information (Y, C
B
, C
R
) directly from the recorded DVD
signal or other video component and one component video output
connector to output it directly into the matrix decoder of the display
device.
By sending the pure DVD component video signal directly, the DVD
signal forgoes the extra processing that normally would degrade the
image. The result is vastly increased image quality, with incredibly
lifelike colors and crisp detail.
Notes:
• This component video output is disable to OSD menu system.
IN
RC-5
DC OUT
AUDIO (AUX2)
COMPONENT VIDEO
DIGITAL OUTDIGITAL IN
SBL
OUT
SL
TV
SW
VCR1DVD
SBL C
SR
MULTI
SR
LC
RSWSBR
DSS
/
VCR2
OUTIN
CDR
/
MD
IN OUT
TAPE
IN OUT
CD
IN OUT
SBR
TV
DVD
OPT
DSS
/
VCR2
TV DVD
COAX
MULTIMONI
IN OUT OUT
S-VIDEO
VIDEO
MONI OUTIN
DVD
VCR1
IN OUT
DSS
/
VCR2
IN OUT
VCR1 DSS/VCR2
MONI OUT
RS-232C
ANTENNA
FM
(
75
Ω
)
GND AM
OUT OUT
SERIAL NO.
SL
R
L
7.1CH
IN
PRE
OUT
AC IN
MODEL NO. SR7300
AC OUTLET
120V 60H
Z
SWITCHED
120W 1A MAX
UNSWITCHED
120W 1A MAX
FRONT A
SURROUND
BACK
FRONT B CENTER SURROUND
SPEAKER SYSTEMS
FRONT A OR B, CENTER, SURROUND, SURR. BACK :
MINIMUM 6 OHMS
FRONT A AND B : MINIMUM 8 OHMS
MULTI
RC
OUT
LRLRLR
654123
L
R
YC
B
/
P
B
C
B
/
P
B
C
B
/
P
B
C
R
/
P
R
YC
R
/
P
R
YC
R
/
P
R
bnvzx c m ,
⁄0
.⁄1⁄5 ⁄2⁄3⁄4
⁄7 ⁄6