Filter
Top Products
6
ENGLISH
REMOTE CONTROL OPERATION
OPERATION
The provided remote control unit is a universal remote controller. The
POWER button x, numeric buttons . and control buttons ⁄2 are used
in common across different input source components.
The input source controlled with the remote control unit changes when
one of the input selector buttons c is pressed.
• Example: To select the DVD as the input source and play the DVD
player.
Press the DVD button c twice within 2 seconds.
The input selector of the SR5200 is switched to DVD and
the remote control unit is set for control of the DVD player.
Press the PLAY button on the remote controller .
FUNCTION AND OPERATION
z Transmitting indicator
Lights up during a button is pressed and an infrared signal is sending.
x Main POWER buttons
Press to switch the power of the SR5200 ON or OFF after pressing the
AMP button c.
c Input selector buttons/ FUNCTION
SELECTOR buttons (AUDIO/VIDEO
INPUT)
Press one of these buttons once or twice to select a particular source
component. For example, to set the receiver to the DVD input, press
the DVD button twice within 2 seconds.
Note:
CDR/MD button is set CDR function at initial. To switch MD function,
press and hold down CDR/MD button and press 2 button ..
To return CDR function, press and hold down CDR/MD button and
press 1 button ..
v MAIN VOLUME UP ( ) /DOWN ( ) buttons
Main volume control of the SR5200. The front, surround, center and
subwoofer channel volumes controlled by these buttons simultaneously.
b MUTE button
Muting button of the SR5200. Press this button decrease the sound
temporarily . Press this button again to return to the previous sound.
n MENU button
This button is used to enter the OSD main menu.
m Cursor buttons ( , , , , OK)
Use these button when operating the setup menu.
See page 10.
, MENU OFF button
This button is used to exit from the setup menu.
. Numeric buttons 1 to 9 (A, B, C ... Z, –) /
Surround mode buttons
Numeric buttons
These buttons are used to enter figures in the selection of a tuner preset
station and station name preset or to set select a CD track number, etc.
The functions of these buttons are dependent on the function button
selected.
Surround mode buttons (when AMP mode is selected)
These buttons are used to select the surround mode.
Note:
The CS5.1 button is unavailable for SR5200.
⁄0 P.SCAN (preset scan) button (when TUNER
mode is selected)
This button is used to start preset scan when SR5200 is selected
TUNER mode.
⁄1 0 / A/D button
0 button
This button is used to enter the number “0”
A/D button (when AMP mode is selected)
This is used to switch between the analog and digital inputs.
⁄2 CONTROL buttons
These buttons are used when operating the CD player, TAPE deck, etc.
The function of these buttons are dependent on the function button
selected.
For the controllable functions of each input function, please refer to fol-
lowing table.
⁄3 ATT (attenuater) button
When the input signal is too high and the voice distorts even by throt-
tling the SR5200 VOLUME control, turn on this function. “ATT” is indi-
cated when this function is activated.
The input level is reduced. Attenuater is invalid for use with the output
signal of “REC OUT”.
⁄4 TREBLE buttons
These buttons are used to adjust the tone control of high frequency
sound for left, center and right speaker.
⁄5 BASS buttons
These buttons are used to adjust the tone control of low frequency sound
for left, center right and subwoofer speaker.
⁄6 MEMO button
Memory enable button for various preset functions.
CHANNEL/SKIP
TUNE/SERCH
TUNE/SERCH
MODE
DSIP/RDS
F.DIRECT
+/A/ANT
–/B/VCR
PTY
CHANNEL/SKIP
TV VCR DVD DSS TUNER CD TAPE CDR MD
CH+
CH—
CH+
CH—
CH+
CH—
TUNING+
TUNING—
FF
REWIND
NEXT
PREV
FF
REWIND
NEXT
PREV
FF
REWIND
NEXT
PREV
FF
REWIND
NEXT
PREV
FF
REWIND
NEXT
PREV
FF
REWIND
NEXT
PREV
REC REC REC REC
PAUSE PAUSE PAUSE PAUSE
PAUSE PAUSE
PLAY PLAY PLAY PLAY PLAY PLAY
STOP STOP STOP STOP STOP STOP
CH
DISPLAY
CH
DISPLAY
FRQ.
DIRECT
VIDEO
VIDEO
TV/VCR
TV/VCR DSS/VCR
DSS/VCR DECK A
DECK B
DISC +
DISC —
DISC +
DISC +
MODE
DIRECTION