Filter
Top Products
17
English
Loading the CD Changer
1 Press 3 CDC to select CD mode.
2 Press OPEN•CLOSE.
™ The CD carousel slides out.
3 Load a CD with the printed side up in
the right tray.
• You can load another disc in the left
tray.
• To load the third disc, press the DISC
CHANGE button.
™ The CD carousel will rotate until the
empty tray is ready for loading.
4 Press OPEN•CLOSE to close the CD
carousel.
™ The total number of tracks and the
playing time of the last selected disc
appear on the display.
Note:
– To ensure good system performance,
wait until the CD changer completely
reads the disc(s) before proceeding.
CD Direct Play
You can play a CD directly by pressing the
DISC 1, DISC 2 or DISC 3 button. The CD
player will stop at the end of playback of
the selected disc.
– A lit button indicates that a disc is
loaded in the disc tray.
Playing a CD
1 Press PLAYÉ to start playback.
™ The disc tray, track number and
elapsed playing time of the current
track appear on the display.
• To interrupt playback, pressÅ.
™ The playing time flashes.
• To resume playback, press PLAYÉ
again.
2 To stop playback, press STOP.
Note:
– All the available discs will play once,
then stop.
Disc Change
You can change the outer two discs while
the third inner disc is stopped or is playing.
1 Press DISC CHANGE.
™ The CD carousel slides out.
2 Replace the discs in the left and right
disc trays.
• If you press DISC CHANGE again
during playback, the CD will stop
playing.
™ The CD carousel will rotate until the
inner tray is rotated out and is ready
for loading.
3 Press OPEN•CLOSE to close the CD
compartment.
CD
Selecting a desired track
Selecting a desired track when
playback is stopped
1 Press S or
T
(or
í
/
ë
on
the remote control)
until the desired
track appears on the display.
2 Press PLAYÉ to start playback.
™ The selected track number and
elapsed playing time appear on the
display.
Selecting a desired track during
playback
• Press S or
T
(less than 0.5
seconds)
until the desired track appears
on the display.
™ The selected track number and
elapsed playing time appear on the
display.
• If you press S
(less than 0.5
seconds)
it will skip to the beginning of
the current track and play the track
again.
Searching for a particular
passage during playback
• Press and hold SEARCH S or
T
(or
à
/
á
on the remote
control)
until the desired passage is
located.
™ The volume will be reduced.
• Play returns to normal when SEARCH
S or T is released.
Programming Tracks
Programming tracks of a loaded CD is
possible when playback is stopped. The
display will indicate the total tracks stored
in the program. Up to 40 tracks can be
stored in the memory in any order. When
40 tracks are stored and you attempt to
store another track, the display will show
“FULL”.
1 Load the desired discs in the disc trays.
2 Press PROGRAM to start programming.
™ The
PROGRAM flag starts flashing.
™ It will cancel any previously selected
repeat mode.
3 Press the 3 CDC button to select the
disc.
4 Press S or
T
(or
í
/
ë
on
the remote control)
to select the desired
track.
5 Press PROGRAM to store the track.
• Repeat steps
3
to
5
to store other discs
and tracks.
6 Press STOP once to end programming.
™ The total number of tracks
programmed and total playing time
appear on the display.
Notes:
– If the total playing time is more than
“
99:59
“
or if one of the programmed
tracks has a number greater than 30,
then “
--:--
” appears on the display
instead of the total playing time.