Filter
Top Products
Before Operation
10
Volume Adjustment
•Turn VOLUME knob clockwise to increase the sound
level, or counterclockwise to decrease it.
• Press VOLUME + to increase the sound level, or use
VOLUME - to decrease it on the Remote Control.
Sound Quality Adjustment
•To activate stereo sound
Select a desired sound mode by using the EQ button
on the front panel or the Remote Control.
Each time you press the button the setting changes in
the display window as shown below.
FLAT → POP → CLASSIC
↑↓
JAZZ ← DRAMA ← ROCK
• Headphone Jack
Connect a stereo headphone plug ( 3.5mm) into the
headphone jack.
The speakers are automatically disabled when you
plug in headphones (not supplied).
MUTE
Press MUTE to turn off the sound, press again to restore.
You can mute your unit in order to answer the telephone.
The “ ” indicator flashes in the display window.
XDSS (Extreme Dynamic Sound System)
Press XDSS button repeatedly to reinforce treble and bass.
XDSS ON → XDSS OFF
MP3 Optimizer
This function is optimizes compressed MP3 file. It provides
improvement to the bass sound. Each time you press MP3
OPT. the setting changes in the following order.
MP3-OPT ON t MP3-OPT OFF
XTS pro
Each time you press XTS pro the setting changes in the fol-
lowing order.
XTS-P ON → XTS-P OFF
SPECTRUM Effect
Each time you press the DISP.MODE button repeatedly
on the Remote Control, you can check the sprectrum
change of 6 types in the display window.
DIMMER
This function dims the LED of the front panel by half in
power-on status .
Press DIMMER once. The LED (Light-emitting diode) of front
panel is turned off. If you press it once more, the display win-
dow will be darken by half. To cancel, press the button again.
Setting the Clock
11
Press CLOCK.
(If the clock requires setting, press and hold CLOCK
for more than 2 seconds.)
- The hours display begins to blink.
22
Select a 24 hour cycle or 12 hour cycle by
pressing
.. bbbb
/
BBBB >>
on the front panel.
33
Press SET/CD
[[ [[
to confirm the selected hour
cycle.
44
Use
.. bbbb
/
BBBB >>
on the front panel to set
the correct hours.
55
Press SET/CD
[[ [[
.
66
Use
.. bbbb
/
BBBB >>
on the front panel to set
the correct minutes.
77
Press SET/CD
[[ [[
and the correct time is shown
on the display window.
ote
When the clock does not appear in the display
window, follow as below.
- In case the clock is set, prese the CLOCK button.
The clock will be shown in the display window for
about 5 seconds.
- In case the clock is not set, the clock will be blinked in the
display window for about 1 minute. Set the clock as above.
Sleep Timer Function
When the sleep timer is set, the unit automatically turns
off after the specified time has elapsed.
1
To specify the time delay before the power is
turned off, press SLEEP.
In the display window you can see SLEEP 180 for
about 5 seconds. This means that the system turns
off automatically after 180 minutes.
22
Each time you press SLEEP the setting changes
in the following order.
SLEEP 180 →150 → 120 →90→80→70 → 60→ 50 → 40 →
30 → 20 →10 → OFF→SLEEP 180...
33
To check the remaining time until the power is
turned off.
While the sleep function is active press SLEEP
briefly. The time remaining until the unit turns off is
displayed for about 5 seconds.
ote
If you press SLEEP while the sleep time is displayed,
the SLEEP time is reset.
To cancel Sleep Timer setting
If you wish to stop the function, press the SLEEP button
repeatedly until “SLEEP 10 ” appears, and then press
SLEEP once again after “SLEEP 10 ” shows on the display.
(12HR)
(24HR)
or