Filter
Top Products
12
|
English
General features
Subwoofer Output
Turning the Subwoofer output ON or OFF.
Hold down on [AM] of the Control knob for at
least 1 second.
Each time you press the button, Subwoofer
output switches ON and OFF.
When it is ON, "SUBWOOFER ON" is displayed.
• You can control this function when "2ZONE" of
<Audio Setup> (page 11) is set to "OFF".
• You can control this item when Speaker Select
Subwoofer of <Sound Management system> (page
13) is set to any item other than "None".
Sound Field Control
1 Select the source to adjust
Press the [SRC] button.
2 Show the Multi-function display
Press the [NEXT] button repeatedly until
"S.F.C" appears.
Refer to <Notes on Multi-function System> (page
9).
3 Enter Sound Field Control mode
Turn the [VOL] knob to select "S.F.C".
Press the [VOL] knob.
• To get the best sound, first set the Cabin Setting
and Speaker Select Front/Rear parameters using the
<Sound Management system> (page 13).
• When "2ZONE" of <Audio Setup> (page 11) is ON, you
cannot select "S.F.C".
4 Select the Sound Field Control item to
adjust
1 Turn the [VOL] knob to select the item you
want to select. Press the [VOL] knob.
2 Press the Control knob.
3 Push the Control knob towards [FM] or
[AM].
12 3
Sound Field control item
"X'Over" "HPF Front" "fc"
"SLP"
Front High Pass Filter Frequency
Front High Pass Filter Slope
"HPF Rear"*¹ "fc"
"SLP"
Rear High Pass Filter Frequency
Rear High Pass Filter Slope
"LPF
SubWoofer"*²
"fc"
"SLP"
"Phase"
Subwoofer Low Pass Filter Frequency
Subwoofer Low Pass Filter Slope
Subwoofer Low Pass Filter Phase
"DTA" "DTA Front" DTA Front
"DTA Rear"*¹ DTA Rear
"DTA
SubWoofer"*²
DTA Subwoofer
"POSI" Position Setting
"Preset" Preset value storage/recalling
• "Preset": You can store an adjusted sound control
value by selecting "Memory". Refer to
<Memory mode> (page 16). Also, you
can recall it by selecting "Recall". Refer to
<Memory Recall mode> (page 16).
• You can adjust "SubWoofer" when <Subwoofer
Output> (page 12) is set to "SUBWOOFER ON".
• X'Over (Crossover Network Setup)
You can manually set a crossover frequency for the
speakers.
• DTA (Digital Time Alignment)
Manually set the sound output timing of each
channel.
• *
1
You can control this item when Speaker Select Rear
of <Sound Management system> (page 13) is set to
any item other than "None".
• *
2
You can control this item when Speaker Select
Subwoofer of <Sound Management system> (page
13) is set to any item other than "None".
5 Adjust the Sound Field Control item
Push the Control knob towards [4] or
[¢].
Each time you push the knob, the setting
alternates between the settings shown in the
table below.
Sound Field Control Item Range
Front High Pass Filter Frequency/
Rear High Pass Filter Frequency
Through/30 — 100/120/150/
180/220/250 (Hz)
Front High Pass Filter Slope/
Rear High Pass Filter Slope/
Subwoofer Low Pass Filter Slope
-12/-18/-24 dB/Oct
Subwoofer Low Pass Filter
Frequency
30 — 100/120/150/180/220/
250 (Hz)/Through
Subwoofer Low Pass Filter Phase Normal/ Reverse