Kenwood KRF-V8030D Stereo Receiver User Manual


 
9
Preparations
OPTICAL
DVD
CD/DVD VIDEO 3 MONITOR
VIDEO 2
COAXIAL
OPTICAL
DIGITAL IN
DIGITAL OUT
OPTICAL
The digital in jacks can accept DTS, Dolby Digital (AC-3), or PCM signals.
Connect components capable of outputting DTS, Dolby Digital (AC-3), or
standard PCM (CD) format digital signals.
If you have connected any digital components to the receiver, be sure to
read the “Input mode settings” section on this page carefully.
Digital connections
To connect an LD player with a DIGITAL RF OUT, connect the LD
player to the KENWOOD RF digital demodulator (DEM-9991D).
Next, connect the DIGITAL OUT jacks of the demodulator to the
DIGITAL IN jacks of the receiver.
Connect the video signal and analog audio signals to the VIDEO
2 or VIDEO 3 jacks. (See "Connecting video components".)
Input mode settings
CD, DVD, VIDEO2, and VIDEO3 inputs each include jacks for digital
audio input and analog audio input.
You must select beforehand which type of input is to be used for each
connected component.
The initial factory setting is to use the digital audio signal for
playback (CD, DVD, VIDEO2, VIDEO3).
To use the analog audio input for playback instead (if, for example, you
have connected a VCR to the VIDEO2 or VIDEO3 input), you must set
the input mode for the corresponding input to the analog mode.
After completing connections and turning on the receiver, follow the
steps below.
1 Use the INPUT SELECTOR knob to select CD, DVD, VIDEO2, or
VIDEO3.
2 Press the INPUT MODE key.
Each press switches the setting as follows:
In DTS play mode
1 D-AUTO (digital input, auto sound)
2 D-MANUAL (digital input, manual sound)
In DVD play mode
1 D-AUTO (digital input, auto sound)
2 D-MANUAL (digital input, manual sound)
3 6CH INPT (DVD 6CH input)
4 ANALOG (analog input, manual sound)
In other mode than DTS or DVD play mode
1 D-AUTO (digital input, auto sound)
2 D-MANUAL (digital input, manual sound)
3 ANALOG (analog input, manual sound)
Digital input:
Select this setting to play digital signals from a DVD, CD, or LD player.
Analog input:
Select this setting to play analog signals from a cassette deck, VCR,
or turntable.
Auto sound:
In the auto sound mode (AUTO SOUND indicator lights), the receiver
selects the listening mode automatically during playback to match the
type of input signal (Dolby Digital, PCM, DTS ) and the speaker setting.
The initial factory setting is auto sound on.
To keep the receiver set to the currently selected listening mode, use
the INPUT MODE key to select “D-MANUAL” (manual sound).
However, even when this setting is selected, there may be cases in
which the listening mode is selected automatically to match a Dolby
Digital source signal depending on the combination of listening mode
and source signal.
Setting up the system
INPUT SELECTOR
INPUT MODE
COAXIAL
DIGITAL
OUT
(AUDIO)
Connect the video signal and analog
audio signals to the VIDEO 2 jacks.
(See "Connecting video components".)
Component with an DTS, Dolby
Digital, or PCM OPTICAL
DIGITAL OUT
Connect the video signal and ana-
log audio signals to the VIDEO 3
jacks. (See "Connecting video
components".)
DOLBY DIGITAL RF
OUT (AUDIO)
COAXIAL DIGITAL OUT
(AUDIO)
OPTICAL DIGITAL OUT
(AUDIO)
LD player
RF digital
demodulator
(DEM-9991D)
(sold separately)
PCM OUT
CD player
Component with an DTS, Dolby
Digital, or PCM COAXIAL
DIGITAL OUT
Optical
fiber
cable
OPTICAL DIGITAL IN
(AUDIO)
MD player
OPTICAL DIGITAL OUT
(AUDIO)