Filter
Top Products
23
Operations
1 Use the INPUT SELECTOR to select the source (CD, DVD or
VIDEO2) you want to record.
2 Set the cassette deck or MD recorder to record.
3 Press and hold the DIMMER key for more than 2 seconds to
select the A-REC or M-REC mode.
1 Rec mode off : The digital input record mode is
switched off.
2 A-REC : The digital input signals (DTS,
Dolby Digital, or PCM) are identi-
fied automatically and converted
into stereo signals that are ready
for recording.
3 M-REC : The input signal type at the mo-
ment this mode is selected is held
throughout this mode.
Recording audio (digital sources)
Switch on the REC mode to record a digital input source.
Usually use the A-REC (Auto-Record) mode to record audio input
sources. When the digital mode changes during recording in the A- REC
mode, the audio input source may be interrupted momentarily.
4 Start playback, then start recording.
Listening to radio broadcasts
Recording video
1 Use the INPUT SELECTOR to select the video source (other than
“VIDEO1”) you want to record.
2 Set the video deck connected to VIDEO 1 to record.
• Select the REC MODE to record a digital input source.
3 Start playback, then start recording.
• Recording may not be normal for some video software. This is due to
the copy guard condition. ·
Recording music in A-REC or M-REC mode
• If the audio reproduction stops in the middle due to change in the
input signals, etc., press the DIMMER key.
• The mode changes every 2 seconds as shown below.
FM
AM
MHz
kHz
3
DOWN MIX
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO
PRO LOGIC
FM
AM
MHz
kHz
3
DOWN MIX
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO
PRO LOGIC
STEREO
STEREO
DIGITAL
AUTO SOUND
DIGITAL
AUTO SOUND
For M-REC mode:
FM
AM
MHz
kHz
3
DOWN MIX
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO
PRO LOGIC
FM
AM
MHz
kHz
3
DOWN MIX
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO
PRO LOGIC
STEREO
STEREO
DIGITAL
AUTO SOUND
AUTO SOUND
DIGITAL
AUTO SOUND
AUTO SOUND
For A-REC mode:
Tuning radio stations
The receiver can store up to 40 stations in the memory and recall them by
one-touch operation.
Recording
INPUT SELECTOR
DIMMER
RC-R0511 RC-R0615/R0617
MULTI CONTROL
INPUT SELECTOR
BAND AUTO/CINEMA EQ.
MULTI
CONTROL
TUNER
AUTO
BAND
1
2
3
Each press switches the tuning method as follows:
4
Auto tuning : The next station is tuned automatically.
Manual tuning : Turn the knob (press the key) to select the
desired station.
Each press switches the band
as follows:
1 AUTO lit (auto tuning)
2 AUTO not lit (manual tuning)
Frequency
display
“TUNED” is displayed when a
station is received.
• Normally, set to “AUTO” (auto tuning). If the radio waves are weak
and there is a lot of interference, switch to manual tuning. (With
manual tuning, stereo broadcasts will be received in monaural.)
“AM” or “FM” indicator
appears in the display
Use the INPUT SELECTOR knob (TUNER key) to select the
tuner.
Use the BAND key to select the desired broadcast band.
Use the AUTO/CINEMA EQ. key to select the desired
tuning method.
Use the MULTI CONTROL keys to select the station.
1 FM
2 AM
“ST.” lights when a broadcast
is being received in stereo.
AM
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
FM
MHz STEREO
AUTO
AM
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
FM
MHz STEREO
AUTO
AM
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
AUTO SOUND
MEMO
FM
MHz STEREO
AUTO
TUNED
ST.
“AUTO” indicator lights up
in the display.
_4942/23-25/EN 3/16/01, 3:08 PM23