Kenwood VR-6070 Stereo System User Manual


  Open as PDF
of 52
 
24
EN
Preparing for surround sound
8 Use the MULTI CONTROL knob or Joystick (5/∞) to select
the appropriate surround speaker setting.
If you selected “LARGE” as the center speaker setting,
1 SURR LARGE : Large surround speakers are con-
nected to the receiver.
2 SURR NML/THX : Average size surround speakers are
connected to the receiver.
3 SURR OFF : Surround speaker setting mode to
the receiver is OFF.
If you selected other than “LARGE” as the center speaker
setting,
1 SURR NML/THX : Surround speaker setting mode to
the receiver is ON.
2 SURR OFF : Surround speaker setting mode to
the receiver is OFF.
• When the setting “SURR OFF” is selected, the procedure skips
to step #.
9 Press the
MM
MM
M key or Joystick (3) again to accept the setting.
• The surround speaker setting indication “SB” appears.
0 Use the MULTI CONTROL knob or Joystick (5/∞) to select
appropriate surround back speaker setting.
If you selected “LARGE” as the surround speaker setting,
1 SB NML/THX : Average size surround back speaker is
connected to the receiver.
2 SB LARGE : Large surround back speaker is
connected to the receiver.
3 SB OFF : Surround back speaker setting mode to
the receiver is OFF.
L
SL S SB SR
CR
SP MUTE
OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
If you selected other than “LARGE” as the surround speaker
setting,
1 SB NML/THX : Surround back speaker setting mode to
the receiver is ON.
2 SB OFF : Surround back speaker setting mode to
the receiver is OFF.
• After setting SB (surround back) from OFF to NML/THX, 6ch
AMP setup display will appear to enable you to re-select either
SW, SB or OFF from the surround back or subwoofer speaker
terminal.
! Press the
MM
MM
M
key or Joystick (3) again to accept the setting
and “SURR:MIX” appears.
• Surr:mix is when the SL and SR speakers signals are mixed to
produce sound from the surround back speaker which would
enable the listener to enjoy sound coming from the back.
L
SL S SB SR
CR
SP MUTE
OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
@ Use the MULTI CONTROL knob or Joystick (5/∞) to select
the following.
1 SURR:MIX ON : Surround mix setting mode to the
receiver is ON.
2 SURR:MIX OFF : Surround mix setting mode to the
receiver is OFF.
• If surround back speaker is turned OFF, SURR:MIX setting is not
visible and the procedure skips to step #.
# Press the
MM
MM
M key or Joystick (3) again to accept the setting.
• The subwoofer re-mix setting indication “SW RE-MIX” appears.
$ Use the MULTI CONTROL knob or Joystick (5/∞ ) to select
the appropriate subwoofer re-mix setting.
1 SW RE-MIX ON : Subwoofer re-mix setting mode to
the receiver is ON.
2 SW RE-MIX OFF : Subwoofer re-mix setting mode to
the receiver is OFF.
• If subwoofer is turned OFF, subwoofer re-mix setting is not
visible.
% Press the SETUP key again to return to the main setup displays.
• The receiver enters the speaker volume level adjustment mode.
• In steps 4 and 5, indications appear only for the selected
channels of the speakers that require adjusting.
4
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
1 Press the
MM
MM
M/
??
??
? keys or Joystick (2/3) to select TEST TONE.
2 Press the SETUP key for the following displays:
1 T.TONE AUTO
2 T.TONE MANUAL
3 The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or Joystick (5/∞).
Press the SETUP key again to begin TEST TONE.
Use the MULTI CONTROL knob or Joystick (5/∞) to adjust
the volume level of the test tone output from the speaker
channel to be adjusted.
For AUTO selection, the first test tone is heard from the front
left speaker for 2.5 seconds. The next test tone is heard from
the speakers in the following sequence for 2 seconds each.
When the 6ch AMP SB has been selected.
LEFT CNTR RIGHT SR
SBSLSUBW
When the 6ch AMP SW or OFF has been selected.
LEFT CNTR RIGHT SR
SBL SBRSLSUBW
The channel indication blinks while the test tone is being output.
L
SL S SB SR
CR
SP MUTE
OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed. °
• If the speaker setting selects are OFF, the speaker level settings
are reset.
For MANUAL selection, press the
MM
MM
M
/
??
??
?
keys or Joystick (2/3)
each time to select the speaker channel.
4 Press the SETUP key again.
• The test tone is turned off and return to the main setup displays.
•VR6070/23-32/EN 3/26/02, 2:32 PM24
 previous next