Filter
Top Products
23
EN
Speaker settings
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
SETUP MULTI CONTROL
POWER ON/OFF
(KRF-X9060D)
POWER
SET UP
Joystick
(MULTI CONTROL5/∞,
DOWN2 /UP3)
POWER
ON/STANDBY
(VR-6070)
ON/STANDBY
(KRF-X9060D)
1
Turn on the power to this receiver by pressing the POWER
ON/STANDBY
(for VR-6070) or POWER ON/OFF and ON/
STANDBY
(for KRF-X9060D) key or POWER key.
2
Press the SETUP key to enter the SETUP mode.
The Surround Back and Subwoofer speaker output selections are
displayed as follows:
1 6ch AMP SB : Surround Back/Subwoofer speaker terminal
will output SB sound. Surround Back pre out
will have output from SBL only.
2 6ch AMP SW : Surround Back/Subwoofer speaker terminal
will have no sound. Surround Back pre out
will have output from SBL and SBR.
3 6ch AMP OFF : It is not advisable to use Surround Back/
Subwoofer speaker terminal for this
selection.
Use the MULTI CONTROL knob or Joystick (5/∞ ) to select the speakers.
Press the SETUP key to proceed to the next SET UP selection.
Use
MM
MM
M
/
??
??
?
keys or Joystick (
2
/
3
) for the following displays.
1 SP SETUP
2 TEST TONE
3 BASS PEAK
4 SP DISTANCE
5 DISP MODE
6 EXIT
The flow of the SET UP is as follows:
SP SETUP TEST TONE BASS PEAK SP DISTANCE EXITDISP MODE
Front Left
Center
Front Right
Surround Right
Surround Back
(Surround Back
Right/Left)
Surround Left
Subwoofer
Display Selector
Display Listen
Subwoofer
Front
Center
Surround
Surround
Back
Surround
Mix
Subwoofer
Re-mix
T. TONE
MANUAL
T. TONE
AUTO
L
C
R
SR
SL
SB
(SBR/SBL)
SW
L
C
R
SR
SB
(SBR/SBL)
SL
SW
3
Select a speaker system.
1 Select the SP SETUP and press the SETUP key again so that
the subwoofer setting indication “SUBW ON” appears.
L
SL S SB SR
CR
SP MUTE
OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
2 Use the MULTI CONTROL knob or Joystick (5/∞) to select
the appropriate subwoofer setting.
1 SUBW ON : Subwoofer setting mode to the receiver is
ON.
2 SUBW OFF : Subwoofer setting mode to the receiver is
OFF.
• The initial setting is “SUBW ON”.
•When the setting “SUBW OFF” is selected, the front speakers
are automatically set to “FRNT LARGE” and the procedure skips
to step 6.
Before step 6, press the SETUP key to accept the setting.
• When subwoofer output sound is required, select “FRNT NML/
THX”, or select both “FRNT LARGE” and “SW RE-MIX ON”.
• After setting SW (subwoofer) from OFF to ON, 6ch AMP setup
display will appear to enable you to re-select either SW, SB or OFF
from the surround back or subwoofer speaker terminal.
3 Press the
MM
MM
M
key or Joystick (3) to accept the setting.
•The front speakers setting indication “FRNT” appears.
L
SL S SB SR
C R
SP MUTE
OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
4 Use the MULTI CONTROL knob or Joystick (5/∞) to select
the appropriate front speakers setting.
1 FRNT LARGE : Large front speakers are connected
to the receiver.
2 FRNT NML/THX : Average size front speakers are con-
nected to the receiver.
•For “FRNT LARGE” selection, no sound will be heard from
subwoofer speaker even when it is set to ON. However, if you
select “SW RE-MIX ON” when subwoofer is selected, you will
be able to hear sound from the subwoofer.
When in STEREO mode, the sound goes directly to front
speaker.
5 Press the
MM
MM
M
key or Joystick (3) to accept the setting.
•The center speaker setting indication “CNTR” appears.
6 Use the MULTI CONTROL knob or Joystick (5/∞) to select
the appropriate center speaker setting.
If you selected “LARGE” as the front speakers setting,
1 CNTR LARGE : A large center speaker is connected
to the receiver.
2 CNTR NML/THX : An average size center speaker is
connected to the receiver.
3 CNTR OFF : Center speaker setting mode to the
receiver is OFF.
If you selected “NML/THX” as the front speakers setting,
1 CNTR NML/THX : Center speaker setting mode to the
receiver is ON.
2 CNTR OFF : Center speaker setting mode to the
receiver is OFF.
7 Press the
MM
MM
M
key or Joystick (3) again to accept the setting.
•The surround speaker setting indication “SURR” appears.
Preparing for surround sound
Continued to next page.
•VR6070/23-32/EN 3/26/02, 2:32 PM23