Filter
Top Products
22
The following basic operations are possible only using the
remote control.
Reinforcing the Bass
You can boost the bass level.
• Once you have made adjustment, it is memorized for each source.
1. Press SOUND.
The 10 keys are activated for sound adjustments.
2. Press BASS BOOST to turn on Bass Boost.
The BASS BOOST indicator lights up.
• Each time you press the button, Bass Boost turns on (“BOOST
ON”) and off (“BOOST OFF”) alternately.
For RX-7030VBK/RX-7032VSL:
You can use the BASS BOOST button on the front panel.
When the Bass Boost is activated, the lamp on the button lights up.
• Each time you press the button, Bass Boost turns on and off.
Notes:
• This function affects only the sounds from the front speakers,
center speaker, and subwoofer.
• When Analog Direct is in use (see page 21), the Bass Boost is
canceled temporarily.
Muting the Sound
Press MUTING to mute the sound through all speakers and
headphones connected.
“MUTING” appears on the display and the volume turns off (the
VOLUME level indicator goes off).
To restore the sound, press MUTING again.
• Turning MASTER VOLUME on the front panel or pressing
VOLUME +/– on the remote control also restores the sound.
Changing the Display Brightness
You can dim the display.
Press DIMMER.
• Each time you press the button, the brightness
level of the display change as follows:
Recording a source
For analog-to-analog recording
You can record any analog playback source onto the recording
components connected to the audio output jacks on the rear of
this unit at the same time.
For digital-to-digital recording
You can record the currently selected digital input source through
the receiver to a digital recording device connected to the
DIGITAL OUT terminal.
Notes:
• Analog-to-digital and digital-to-analog recordings are not
possible.
• The output volume level, Midnight Mode (see page 20), Bass
Boost (see the left column), Digital Equalization (see page 32),
Surround modes and DSP modes (see pages 34 to 39) cannot
affect the recording.
Basic adjustment auto memory
This receiver memorizes sound settings for each source—
• when you turn off the power,
• when you change the source, and
• when you assign the source name (see page 21).
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Analog/digital input mode (see pages 19 and 20)
• Input attenuator mode (see page 20)
• Analog Direct (see page 21)
• Digital Equalization (see page 32)
• Speaker channel output levels (see page 32)
• Surround and DSP mode selection (see pages 37 and 39)
• Bass Boost setting (see the left column)
Notes:
• If the source is FM or AM, you can assign a different setting for
each band.
• If you want to memorize the volume level with the above
settings, set One Touch Operation to “ON” (see page 30).
Using the Sleep Timer
Using the Sleep Timer, you can fall asleep while listening to music.
When the shut-off time comes, the receiver turns off automatically.
Press SLEEP repeatedly.
The SLEEP indicator lights up on the display, and the shut-off time
changes in 10 minutes intervals:
To check or change the time remaining until the shut-off time:
Press SLEEP once.
The remaining time until the shut-off time appears in minutes.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer:
Press SLEEP repeatedly until “SLEEP 0min” appears on the display.
(The SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.
231
564
89
7/P
0
+10
BOOST
BASS
MUTING
DIMMER
SLEEP
10/0
SOUND
Reinforcing the
Bass
Using the Sleep
Timer
Muting the
Sound
Changing
the Display
Brightness
2010 30 40 50 60 70 80 90
(Canceled)
0
Dimmer Much dimmer
Canceled
(Normal display)
RX-7030V
RX-7032V
ONLY
17-22_8030&7030[J]10.pm6 03.2.13, 2:45 PM22