Filter
Top Products
23
English
3. Close the holder gently.
When both Deck A and Deck B contain a tape, the last deck to have a tape inserted is selected.
To change the selected deck, press the DECK A/B button. When using the Remote Control, press the
A or B button.
4. Press the ¤ TAPE ‹ button (or ™ or £ button on the Remote
Control).
The tape is played in the direction of the button pressed for the selected deck.
• The Cassette Deck automatically stops when one side of a tape has finished playing.
To stop playing, press the 7 button.
To remove the tape, stop the tape, and press the 0 EJECT button.
To change deck while playing a tape, press the ¤ TAPE ‹ button after pressing the DECK A/B
button on the Unit or press the ™ or £ button after pressing the A or B button on the Remote Control.
Fast Left And Fast Right——————————————————
o While the tape is stopped, press the 4 P.DOWN button (or 1 button on the Remote Control) and
the tape will wind rapidly onto the left side of the cassette without playing.
o While the tape is stopped, press the ¢ P.UP button (or ¡ button on the Remote Control) and the
tape will wind rapidly onto the right side of the cassette without playing.
Note: Deck A and Deck B cannot be used for playback at the same time.
Music Scan
To find the beginning of a music track during play, use the Music Scan function. Music Scan searches for
blank portions that usually separate selections, then plays the next selection.
To Find the Beginning of the Current Selection——————
Press the 4 P.DOWN or ¢ P.UP button (or the 1 or ¡ button on
the Remote Control) during play.
o Make sure that you press the 4 P.DOWN or ¢ P.UP button (or the 1 or ¡ button on the
Remote Control) in the opposite direction to that in which the tape is playing. Searching stops at the
beginning of the current selection, and the current selection starts automatically.
To Find the Beginning of the Next Selection ———————
Press the 4 P.DOWN or ¢ P.UP button (or the 1 or ¡ button on
the Remote Control) during play.
o Make sure that you press the 4 P.DOWN or ¢ P.UP button (or the 1 or ¡ button on the
Remote Control) in the same direction as that in which the tape is playing. Searching stops at the
beginning of the next selection, and the next selection starts automatically.
Music Scan works by detecting a 4-second long blank at the beginning of each selection,
so it won’t work well if your tape has:
• No blank at the beginning of a selection .
• Noise (often caused by much use or poor quality dubbing) which fills the blank with noise.
• Long, very soft passages or pauses in a selection. The scan will detect these as 4-second long
blanks. If this happens, just scan again until you reach the selection you want.
Reverse Mode
You can play both sides of a cassette, or play both the tapes in the two Cassette Decks continuously.
Press the REVERSE MODE button to switch to Reverse Mode.
The indicator changes with each press of the button as shown.
= = = = (back to the beginning)
: The Cassette Deck automatically stops after playing one side of the tape.
: The Cassette Deck automatically stops after playing both sides of the tape being played (or set
to play).
: After playing both sides of the tape being played (or set to play), the Unit always checks to
see if a tape is in the other deck. If there is, it automatically starts playing that tape. This
Continuous Play function works regardless of which deck starts first. The tapes are played
continuously until the 7 button is pressed.
DECK A/B REVERSE MODE
CD
TAPE
AUX
FM
/AM
P. UPP. DOWN
P. UPP. DOWN
DECK A/B REVERSE MODE
CA-D351/451TR[E]/EN 97.4.16, 9:40 AM23